MVME5100 Single Board Computer Installation and Use - Bustec

More documents

Recommendations

Info

Operation2Reset FunctionWhen toggled to RST, the switch resets all on-board devices. To generatea reset, the switch must be depressed for more than five seconds.The on-board Universe ASIC includes both a global and a local resetdriver. When the ASIC operates as the system controller, the reset driverprovides a global system reset by asserting the SYSRESET# signal.Additionally, when the MVME5100 is configured as a system controller(SCON), a SYSRESET# signal may be generated by toggling the ABT/RSTswitch to RST, or by a power-up reset, or by a watchdog timeout, or by acontrol bit in the Miscellaneous Control Register (MISC_CTL) in theUniverse ASIC.NoteSYSRESET# remains asserted for at least 200 ms, as required bythe VMEbus specification.Safe RestartIn case the Vital Product Data (VPD) is lost, the following steps willgenerate a “safe restart” on the MVME5100.1. Depress the ABT/RST switch (do not release until step 3).2. Wait until the DS1 LED (amber) lights. At this point, both DS1 andDS2 LEDs are lit.3. Release the ABT/RST switch.4. Wait about 1/2 to 1 second.5. Depress the ABT/RST switch and hold for approximately 1 second.NoteFor visual feedback while practicing this technique, turn on theDebug Startup codes through ENV. During the reset, a line isdisplayed indicating the state of the MMU, RAM, VPD, and SafeStart mode. The Safe Start flag should be set indicating a restartusing built-in defaults in progress. Even though theVPD_VALID flag may be set, the data from VPD is not used in2-2 Computer Group Literature Center Web Site
Switches and Indicatorsthis mode. For more information on the VPD, refer toAppendix B of the MVME5100 Single Board ComputerProgrammer’s Reference Guide listed in Appendix D, RelatedDocumentation.2Status IndicatorsRST Indicator (DS1)CPU Indicator (DS2)There are two light-emitting diode (LED) status indicators located on theMVME5100 front panel. They are labeled BFL and CPU.The yellow BFL LED indicates board failure; this indicator is alsoilluminated during reset as an LED test. The BFL is set if the MODFAILRegister or FUSE Register is set. Refer to the MVME5100 Single BoardComputer Programmer’s Reference Guide (V5100A/PG) for informationon these registers.The green CPU LED indicates CPU activity.Connectors10/100BASET PortsThere are three connectors on the front panel of the MVME5100. Two arebottom-labeled 10/100BASET and one is labeled DEBUG.The two RJ-45 ports labeled 10/100BASET provide the10BaseT/100BaseTX Ethernet LAN interface. These connectors are toplabeledwith the designation LAN1 and LAN2.http://www.motorola.com/computer/literature 2-3
Page 1 and 2: MVME5100Single Board ComputerInstal
Page 4: FlammabilityAll Motorola PWBs (prin
Page 7 and 8: ContentsAbout This ManualSummary of
Page 9 and 10: IDSEL Routing......................
Page 11: List of FiguresFigure 1-1. MVME5100
Page 14 and 15: xivTable D-1. Motorola Computer Gro
Page 16 and 17: Model NumberMVME5101-216xMVME5110-2
Page 18 and 19: Summary of ChangesThis is the third
Page 20 and 21: Appendix C, RAM500 Memory Expansion
Page 22 and 23: An asterisk (*) following a signal
Page 24 and 25: 1Hardware Preparation and Installat
Page 44 and 45: Operation2DEBUG PortThe RJ-45 port
Page 47 and 48: 3PPCBug Firmware3IntroductionThe PP
Page 49 and 50: Using PPCBugImplementation and Memo
Page 51 and 52: Using PPCBug8. Delays for 750 milli
Page 53 and 54: Default SettingsCNFG - Configure Bo
Page 55 and 56: Default SettingsNote:The bug does n
Page 57 and 58: Default SettingsPrimary SCSI Data B
Page 59 and 60: Default SettingsAuto Boot Abort Del
Page 61 and 62: Default Settings!CautionIf you use
Page 63 and 64: Default SettingsSerial Startup Code
Page 65 and 66: Default SettingsThe configured valu
Page 67 and 68: Default SettingsSpecial PCI Slave I
Page 69 and 70: Standard CommandsTable 3-1. Debugge
Page 71 and 72: Standard CommandsTable 3-1. Debugge
Page 73: Standard CommandsPPCBug Diagnostics
Page 76 and 77: Functional DescriptionTable 4-1. MV
Page 78 and 79: Functional DescriptionThe following
Page 80 and 81: Functional DescriptionApplication N
Page 82 and 83: Functional DescriptionVMEbus Interf
Page 85 and 86: 5Pin Assignments5IntroductionThis c
Page 87 and 88: ConnectorsTable 5-1. Jumper Switche
Page 89 and 90: ConnectorsTable 5-3. Memory Expansi
Page 91 and 92: ConnectorsTable 5-3. Memory Expansi
Page 93 and 94:
ConnectorsTable 5-4. PCI Expansion
Page 95 and 96:
ConnectorsPCI Mezzanine Card (PMC)
Page 97 and 98:
ConnectorsTable 5-6. PMC Slot 1 Con
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
ConnectorsTable 5-11. PMC Slot 2 Co
Page 107 and 108:
ConnectorsTable 5-12. PMC Slot 2 Co
Page 109 and 110:
ConnectorsTable 5-13. VMEbus Connec
Page 111 and 112:
ConnectorsTable 5-14. VMEbus P2 Con
Page 113 and 114:
ConnectorsTable 5-15. VMEbus Connec
Page 115:
ConnectorsCOM1 and COM2 Connector P
Page 118 and 119:
Programming the MVME51xxProcessor B
Page 120 and 121:
Programming the MVME51xxNotes1. Pro
Page 122 and 123:
Programming the MVME51xxEstablishin
Page 124 and 125:
Programming the MVME51xxPCI Arbitra
Page 126 and 127:
Programming the MVME51xxThe arbitra
Page 128 and 129:
Programming the MVME51xxThe MVME51x
Page 130 and 131:
Programming the MVME51xxEndian Issu
Page 133 and 134:
ASpecificationsAThis appendix lists
Page 135:
Cooling RequirementsACooling Requir
Page 138 and 139:
Solving Startup ProblemsBII. There
Page 140 and 141:
Solving Startup ProblemsBV. The deb
Page 142 and 143:
Functional DescriptionFunctional De
Page 144 and 145:
Functional DescriptionCA,BA,WE_L,RA
Page 146 and 147:
RAM500 Module Installationthat stan
Page 148 and 149:
RAM500 ConnectorsTable C-3. RAM500
Page 150 and 151:
RAM500 ConnectorsTable C-3. RAM500
Page 152 and 153:
RAM500 Programming IssuesTable C-4.
Page 155 and 156:
DRelated DocumentationDMotorola Com
Page 157 and 158:
Related DocumentationTable D-2. Man
Page 159 and 160:
IndexAAbort (interrupt) signal 2-1A
Page 161 and 162:
MVME510x 1-16MVME510x hardware 1-8M
Page 163:
features C-1install instructions C-
show all

MVME5100 Single Board Computer Installation and Use - Bustec

Create successful ePaper yourself

Delete template?

Save as template?