Verification <strong>Kits</strong>INTRODUCTION: When purchasing an Open-Short-Load-Through Kit, or a LRL/TRLKit, <strong>Spectrum</strong> <strong>Elektrotechnik</strong> <strong>GmbH</strong> will assure that the components are in superior condition.But by using the Kit day after day, the components may wear out, or degrade to anunacceptable extent. The Verification Kit is supplied to verify that the <strong>Calibration</strong> Kit stilloperates within the limits, or to identify the problems with certain <strong>Calibration</strong> Components.EQUIPMENT PROVIDED: Each Verification Kit contains as a minimum one “ideal” airlinesof 50 Ohms, and a Mismatch of 25 Ohms. Both units consist of separate Outer Conductorsand Center Conductors.In the Instrument Case is a certain space available where a Torque Wrench, and a set of singleended wrenches, supplied on separate order, can be fitted.To install the Airline, or the Mismatch, please proceed as follows:1. Install the Outer Conductor at one of the Test Connectors.2. Insert the Center Conductor into the Outer Conductor of the Airline, or theMismatch, respectively. Please use the especially designed Insertion Tool.3. Extract the Insertion Tool and connect carefully the second Test Connector.TORQUE WRENCHES: In order to ensure proper mating of the connectors, it is highlyrecommended to always use Torque Wrenches. They do not only ensure proper connection ofthe components, they also help to prevent overtorquing, which may damage or degrade theperformance of these expensive “ideal” components.CONNECTOR SERIES: Verification <strong>Kits</strong> are available in the following connector series:2.4mm, 2.9mm, 3.5mm, 7mm, N and <strong>SMP</strong>.PHASE STABLE CABLE ASSEMBLIES: <strong>Spectrum</strong> <strong>Elektrotechnik</strong> <strong>GmbH</strong> offers a seriesof Phase Stable Assemblies, fitted at one side with the appropriate NMD connector for directconnection with the Vector Network Analyzers of Hewlett Packard and Wiltron, and with2.4mm, 3.5mm, K*, <strong>SMP</strong>, N, etc., males and females at the other end of the Assembly.Ordering Information for Verification <strong>Kits</strong>V E - C D E F42B: to be replaced withone of the followingletters for theoption required.S = Standard KitP = Professional KitCDEF: to be replaced with one of thefollowing digit number/letter Code,describing Connectors as listed below.2400292035007000N000<strong>SMP</strong>0======2.4mm2.9mm3.5mm7mmN<strong>SMP</strong><strong>Spectrum</strong> <strong>Elektrotechnik</strong> <strong>GmbH</strong> P.O. Box 45 05 33, 80905 Munich, Germany Tel. (89) 354 804-0, Fax (89) 354 804-90 (Country Code: 49)* 'K' Connector is a trademark of Wiltron Company.Date: 03.98trefli.pm6
Verification <strong>Kits</strong>12Description of Equipment ProvidedStandard <strong>Calibration</strong> Kit1: Airline 50 Ohms2: Mismatch 25 Ohms15: Instrument caseOperating instructionsProfessional <strong>Calibration</strong> Kit1311212 4Description of Equipment Provided Professional <strong>Calibration</strong> Kit1: Airline 50 Ohms2: Mismatch 25 Ohms4: Set of Double ended wrenches15: Instrument casetrefli.pm63: Torque wrenchOperating instructions<strong>Spectrum</strong> <strong>Elektrotechnik</strong> <strong>GmbH</strong> P.O. Box 45 05 33, 80905 Munich, Germany Tel. (89) 354 804-0, Fax (89) 354 804-90 (Country Code: 49)43