T E C H N IC A LD A TA - UPgates

More documents

Recommendations

Info

Safety and hygiene at work: When following basic hygiene rules SANAKRYL UV is not a health hazard. It is necessary to use suitable protective clothing, gloves and goggles. Wash skin with soap and water, in case of contact with eyes, fl ush immediately with plenty of water. If irritation does not stop, seek medical advice. If accidentally swallowed seek medical advice. Do not induce vomiting. ›› 56
›› Serial Number 9710 waterproof sealing compound for protection, repair and rehabilitation of flat roofs made of asphalt strips and polyurethane foam Features: SANAKRYL TOP is a single-component water-based waterproofing material prepared from the aqueous copolymer dispersions, pigments, fi llers and special additives. Flexible isolating mass SANAKRYL TOP is applied in liquid form and dries creating seamless waterproofing permanently fl exible fi lm with minimal water absorption, satisfying requirements for long-term exposure to water and weather conditions. SANAKRYL TOP along with a reinforcing fabric is a waterproof system for the repair of fl at roofs with slope of min. 1° and longterm water stress, maximum 6 months continuously without drying. The system is designed as a primary anchor and as a fi nal sealing layer with SANAKRYL TOP. This system is used to protect, maintain and repair older roofi ng materials from asphalt strips. SANAKRYL TOP can be used in fi re hazard zones on the roofs at an angle of 15 °. Other uses: SANAKRYL TOP can be also used as a protective coating and as a new roof insulating polyurethane foam. As a protective coat of polyurethane foam roof insulation, SANAKRYL TOP has a fi re classifi cation of E. Simultaneously with the roofi ng paint SANAKRYL TOP can also be used to coat roof accessories of galvanized metal, aluminum and steel sheet coated with anticorrosive paint. It iss not intended for maintenance and repair of foil coverings. Technical data: Dry matter min. 65 wt. % Spec. Weight 1.4 g /cm3 pH 8,0–10,0 Viscosity Brookfi eld (A/5/10) 13-21 Pas (23°C) Water resistance 0.0 l/m2 per hour Absorption max. 5 % Tensile strength 1.5 MPa Elongation 150 % Surface adhesion min. 0.5 MPa Consumption: 0.5–1.0 kg/m2 - protective coating (1 layer) 2.5–3.0 kg/m2 - waterproofi ng system with fabric (3 layers) Shades: light gray, russet Packaging: 25 kg plastic containers, 100 kg returnable drums with PE liner Storage: Store (in the original unopened packaging) between 5–25°C. It must not freeze! ›› ver. 01-11 Types of surfaces: asphalt strips, sheet steel painted with anticorrosive paint or galvanized sheet metal, aluminum, polyurethane foam Surface preparation: The surface must be clean of mechanical impurities and grease (high pressure washer, solution concentrate ETERNAL odmašťovač, or other suitable detergent) repaired, and dry. Absorbent materials and old asphalt roofi ng must be primed, with e.g. FORTE penetral primer. Application: SANAKRYL TOP is applied to the prepared surface with an asphalt brush or roller (roller, only the last layer) in two or three coats according to the type of adjustment, with a break 12 hours at a temperature around 20 °C. SANAKRYL TOP is designed for roofs with a minimum slope of 1° and a long-term water stress - but no longer than 6 months continuously without being dry. In places with heavy precipitation, it is necessary to use a waterproofi ng system with a reinforcing fabric. Application on asphalt strips We recommend properly repairing larger cracks (sealant prepared from the addition of SANAKRYL TOP and quartz sand with maximum grain size 0.5 mm) and bulges (excision and relabelling). SANAKRYL TOP is intended as basic as a top layer. The basic layer is applied to the properly prepared surface. Waterproofi ng system: For waterproofi ng layers to meet the imposed demands, it is necessary to use reinforcing fabric. The fabric is put into the fi rst fresh layer of SANAKRYL TOP. Total 2-3 layers are applied to the fabric in the entire area covered by SANAKRYL TOP. The last layer is a minimum usage of 1 kg / m2. Minimum total consumption of SANAKRYL TOP is 2.5 kg / m2. Protective coating: SANAKRYL TOP can be applied as a protective coating with a consumption 0.5-1 kg / m2. It is a protective coating that has properties of waterproofi ng systems. Protective polyurethane foam paint for roof: SANAKRYL TOP polyurethane foam is designed as a protective coating for thermal insulation of roofs from polyurethane foam. Application can be made within 7 days upon application by spaying, brush or broom. For spraying, it can be diluted in a solution of 10% water. SANA- KRYL TOP is applied in one layer. Consumption: 1.0 kg/m2 Protective coating for metal roof components: SANAKRYL TOP creates a complete seamless fl exible foil with high adhesion and works cooperatively with the ground. Prevents ›› 57
Page 1 and 2: AUSTIS Technical data
Page 3 and 4: mat akrylátový ›› Serial Numb
Page 5 and 6: mat Revital ›› Serial Number 05
Page 7 and 8: lesk akrylátový ›› Serial Num
Page 9 and 10: lesk alkydový ›› Serial Number
Page 11 and 12: odmašťovač ›› Serial Number
Page 13 and 14: na radiátory ›› Serial Number
Page 15 and 16: na střechy ›› Serial Number 07
Page 17 and 18: na dřevo napouštědlo ›› Seri
Page 19 and 20: lazura tenkovrstvá ›› Serial N
Page 21 and 22: PUR lak ›› Serial Number 0104 o
Page 23 and 24: IN plus ›› Serial Number 9518 e
Page 25 and 26: IN Thermo ›› Serial Number 0917
Page 27 and 28: epoxy stabil ›› Serial Number 9
Page 29 and 30: op-izol ›› Serial Number 9404 w
Page 31 and 32: elast ›› Serial Number 9704 spe
Page 33 and 34: akrylát ›› Serial Number 9515
Page 35 and 36: silikon PREVENSIL ›› Serial Num
Page 37: ›› Serial Number 9402 waterproo
Page 41 and 42: ›› Serial Number 9510 Universal
Page 43 and 44: UNI ›› Serial Number 0202 one c
Page 45 and 46: 1K Warning: Insulation material mad
Page 47 and 48: (experimentally up to 10 wt.% liqui
Page 49 and 50: opravný beton ›› Serial Number
Page 51 and 52: adhezní můstek ›› Serial Numb
Page 53 and 54: PNO ›› Serial Number 9514 pigme
Page 55 and 56: flex ›› Serial Number 0918 flex
Page 57 and 58: akrylátová omítkovina ›› Ser
Page 59: AUSTIS a.s. K Austisu 680 154 00 Pr

T E C H N IC A LD A TA - UPgates

Create successful ePaper yourself

Delete template?

Save as template?