Synchronous servomotors DBL/DBK - BIBUS SK, sro

More documents

Recommendations

Info

Installation / Setup 01/2004 Kollmorgen II.2 Assembly / Wiring Only qualified staff with knowledge of mechanical engineering are permitted to assemble the motor. Only staff qualified and trained in electrical engineering are allowed to wire up the motor. The procedure is described as an example. A different method may be appropriate or necessary, depending on the application of the equipment. Warning! Protect the motor from unacceptable stresses. Take care, especially during transport and handling, that components are not bent and that insulation clearances are not altered. Always make sure that the motors are de-energized during assembly and wiring, i.e. No voltage may be switched on for any piece of equipment which is to be connected. Ensure that the switch cabinet remains turned off (barrier, warning signs etc.). The individual voltages will only be turned on again during setup Note! The ground symbol �, which you will find in the wiring diagrams, indicates that you must provide an electrical connection, with as large a surface area as possible, between the unit indicated and the mounting plate in the switch cabinet. This connection is to suppress HF interference and must not be confused with the PE (protective earth) symbol (protective measure to EN 60204). To wire up the motor, use the wiring diagrams in the Installation and Setup Instructions of the servoamplifier which is used. 14 Servomotors DBL/DBK
Kollmorgen 01/2004 Installation / Setup The following notes should help you to carry out the assembly and wiring in an appropriate sequence, without overlooking anything. Site Ventilation Assembly Cable selection Earthing Shielding Wiring Check The site must be free of conductive and aggressive material. For V3-mounting (shaft end upwards), make sure that no liquids can enter the bearings. If an encapsulated assembly is required, please consult our applications department beforehand. Ensure an unhindered ventilation of the motors and observe the permissible ambient and flange temperatures. For ambient temperatures above 40°C please consult our applications department beforehand. During assembly, take care that the motor is not overstressed when it is fixed in place. Select cables according to EN 60204 See the table in chapter II.1 when cable length exceeds 25m. Use correct earthing and EMC-shielding according to the Installation instructions for the servoamplifier which is used. Earth the mounting plate and motor casing. For connection methods see chapter II.2.1. — Route power cables as separately as possible from control cables — Connect up the resolver or encoder. — Connect the motor leads, install motor chokes close to the — servoamplifier, connect shields to shielding terminals or EMC — connectors at both ends — Connect the holding brake, if used, Connect shielding at both ends. Final check of the installed wiring, according to the wiring diagram which was used Servomotors DBL/DBK 15
Page 1 and 2: www.DanaherMotion.com Synchronous s
Page 3 and 4: Kollmorgen 01/2004 Contents Content
Page 5 and 6: Kollmorgen 01/2004 Important notes
Page 7 and 8: Kollmorgen 01/2004 General I Genera
Page 9 and 10: Kollmorgen 01/2004 General I.5 Stan
Page 11 and 12: Kollmorgen 01/2004 General I.6 Opti
Page 13: Kollmorgen 01/2004 Installation / S
Page 17 and 18: Kollmorgen 01/2004 Installation / S
Page 19 and 20: Kollmorgen 01/2004 Installation / S
Page 21 and 22: Kollmorgen 01/2004 Technical data I
Page 23 and 24: Kollmorgen 01/2004 Technical data D
Page 25 and 26: Kollmorgen 01/2004 Technical data T
Page 65 and 66:
Kollmorgen 01/2004 Technical data T
Page 67 and 68:
Kollmorgen 01/2004 Technical data D
Page 69 and 70:
Kollmorgen 01/2004 Appendix IV Appe
Page 71 and 72:
Kollmorgen 01/2004 Appendix IV.3 In
show all

Synchronous servomotors DBL/DBK - BIBUS SK, sro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?