User-Service Manual - Joerns

More documents

Recommendations

Info

Joerns® Bed FramesUltraCare®XT12To Remove AC Power CordRecommended Tools: Small Screwdriver,Masking Tape, Zip Ties, 5/16" Nut Driver1. Raise bed so that there is about 27 inches ofclearance between floor and sleep surface of bed.2. Unplug power cord from wall outlet.3. Cut cable ties that hold AC power cord to frame.Tape remaining cords in their original position. It isvery important to keep motor cords routed alongframe in original factory-installed positions. If thisstep is not followed, damage to cords or electricshock may result.4. Detach ground wire from bed frame if equipped.Warning: Possible Shock Hazard.Injury may result from improper power cordrouting. Always follow proper factory-installedrouting configuration. Be sure to check conditionof power cord on a regular basis. Do not usedamaged or frayed power cords.5. Using a small screwdriver, alternately depresssmall red latch tabs above and below AC inletreceptacle on the control box. Simultaneously,pull gently outward on AC power cord where itconnects to control box, until plug comes out.6. Plug replacement cord into control box until itlatches. Attach ground wire to bed frame.7. Re-route AC power cord along frame in sameposition as original routing.8. Replace cable ties along with cords in their originalposition and routing to the control box. If this stepis not followed, damage to cords or electric shockmay result.TroubleshootingAny loss of electrical function should be investigatedwith the following steps:EventBed notrespondingto pendantcontrolBed notrespondingto staffcontrolAll lockoutsindicatorsflashingHi-Lo lockoutindicatorflashingKneeLockoutindicatorflashes whenattemptingarticulationPossible Remedies1. Check lockout status.2. Check connection is fully insertedwith cable secured.3. Check the bed is plugged intopower source and control boxgreen light is illuminated.4. Unplug bed for 60 seconds andplug back in.5. If these steps fail to resolve theproblem, call Technical Supportat 800-826-0270.1. Check lockout status.2. Check connection is fully insertedwith cable secured.3. Check the bed is plugged intopower source and control boxgreen light is illuminated.4. Unplug bed for 60 seconds andplug back in.5. If these steps fail to resolve theproblem, call Technical Supportat 800-826-0270.1. Unplug bed for 60 seconds andplug back in.2. Push and hold Hi-Lo up anddown on staff control or pendantsimultaneously until flashing stops(No more then 15 seconds).3. If these steps fail to resolve theproblem, call Technical Supportat 800-826-0270.1. Thermal overload condition. Thisshould self correct in 2 minutesor less. Do not surpass 10% dutycycle (2 min on/ 18 min off).2. If these steps fail to resolve theproblem, call Technical Supportat 800-826-0270.1. Bed is in a reverse Trendelenburgor comfort chair position, level bed(page 9, Figure 18, button 8).2. Lower or raise Hi-Lo to endof travel3. If these steps fail to resolve theproblem, call Technical Supportat 800-826-02701. Switch pendant with a new pendant or one from abed that is functioning normally.2. If these steps fail to resolve the problem, callTechnical Support at 800-826-0270.© 2013 Joerns Healthcare • 6110045 RevG • 13-2216
Joerns® Bed FramesUltraCare®XTNote: Electrical damage can occur if a non-approvedpendant is connected to the electrical system.MaintenanceMaintenance/inspection Information:Visually inspect the bed and accessories for brokenwelds or cracks and check for loose hardware on amonthly basis.If any broken welds or cracks are found, removebed from service immediately and replace affectedpart(s). If necessary, contact Technical Support,800-826-0270, for assistance. Tighten any loosehardware.Preventative MaintenanceTo ensure maximum life of your product, followall warnings and cautions in the User Manual andmaintain your bed with care, as outlined below. Themaintenance required will be dictated by your bed’susage and care – a thorough inspection should beconducted monthly.To Maximize Service Life1. If you have a Joerns ® Care 100, or EasyCare ®3, 5, or 7, run the bed frame to either the highestposition or lowest position once a day. Thisensures that the bed frame remains level. JoernsUltraCare ® XT and EasyCare 9 bed frames haveself-leveling electronics and do not require thisprocedure.2. Keep the bed clean.3. Observe bed operation and report anydiscrepancies or problems to Joerns HealthcareTechnical Support at 800.826.02704. After initial week of use, check all threadedfasteners for looseness, and make sure all pinsare in their normal location and fastened securely.Check monthly for loose bolts, nuts, pins and otherretaining hardware. Tighten any loose hardware,and contact Joerns Healthcare to order anyappropriate service parts.5. Make sure each inspection includes the undersideof the bed frame and mattress support platform.6. Visually inspect the bed frame and accessoriesfor any cracking, bending, or hole enlargement.If found, contact Joerns Technical Support at800.826.0270, remove the bed from serviceimmediately, and replace the affected parts.7. Check wiring for proper connections and damage(fraying, kinking, or deterioration). Reportany damage to Joerns Technical Support at800.826.02708. Check actuators for correct mounting atattachment points and ensure all related pins aremounted securely and properly to the bed frame.Actuators are not serviceable, but are replaceableif required.9. Lubricate pivot point, pins and bolts as required.The recommended lubricant is Joerns-approvedgrease #12500013, available from JoernsTechnical Support at 800.826.0270.If any discrepancies are noted during inspection,they must be corrected before continuing bed frameuse. Major service and repairs must be performedby authorized Joerns Healthcare Technical Support,which you may contact at 800.826.0270.CleaningCaution: Possible damage to electrical parts, and/orshock hazard.1. Clean all electrical components (motors, controlbox, pendant and cords) on your Joerns ® bed withdamp, well-wrung out cloth. Excess water in or onelectrical parts, could damage these components.Do not submerge pendant in liquid.2. Your Joerns bed features durable, baked-on epoxyfinish that is easily cleaned with mild solution ofantiseptic cleaner and warm water. Read andfollow all label instructions on your cleaningproducts.3. Wood veneer surfaces should be maintained bycleaning with furniture cleaner or polish.13© 2013 Joerns Healthcare • 6110045 RevG • 13-2216
Page 9: Joerns® Bed FramesUltraCare®XTSta
Page 15 and 16: Joerns® Bed FramesUltraCare®XTHea
Page 17 and 18: Joerns® Bed FramesUltraCare®XTBat

User-Service Manual - Joerns

Create successful ePaper yourself

Delete template?

Save as template?