UHF-RW-MP-232-V1 - RFID Shop

More documents

Recommendations

Info

Respond:Len Adr reCmd Status Data[] CRC-160x05 0xXX 0x24 0x00 ----- LSB MSBNotes: The Adr is old address, not new address.8.4.4 Set Scan TimeThe host sends this command to change the value of InventoryScanTime of the reader.The value is stored in the reader’s inner EEPROM and is nonvolatile after reader powered off.Command:Data[]Len Adr CmdCRC-16Scantime0x05 0xXX 0x25 0xXX LSB MSBParameter Connect:Scantime: Inventory Scan Time. The default value is 0x0A (corresponding to10*100ms=1s). The value range is 0x03-0xFF (corresponding to 3*100ms-255*100ms).When the host tries to set value 0x00-0x02 to InventoryScanTime, the reader will set it to0x0A automatically. In various environments, the actual inventory scan time may be 0-75mslonger than the InventoryScanTime defined.Respond:Len Adr reCmd Status Data[] CRC-160x05 0xXX 0x25 0x00 ----- LSB MSB8.4.5 Set Band RateThe host sends this command to change the value of band rate of the reader. The valueis stored in the reader’s inner EEPROM and is nonvolatile after reader powered off.Command:Len Adr CmdData[]BaudRateCRC-160x05 0xXX 0x28 0xXX LSB MSBParameter Connect:BaudRate: The serial port baud rate default value is 57600 bps. BaudRate is 0 - 6,defined as follows:BaudRate Bps0 9600bps1 19200 bps2 38400 bps3 43000 bps4 56000 bps5 57600 bps6 115200 bpsRespond:34
Len Adr reCmd Status Data[] CRC-160x05 0xXX 0x28 0x00 ----- LSB MSBNotes: The response of the baud rate for the original baud rate, and next command usesthe new band rate.8.4.6 Set PowerThe host sends this command to change the power of the reader. The value is stored inthe reader’s inner EEPROM and is nonvolatile after reader powered off.Command:Data[]Len Adr CmdCRC-16Pwr0x05 0xXX 0x2F 0xXX LSB MSBParameter Connect:Pwr: New power. The default value is 18(about 30dBm), it range is 0-18.Respond:Len Adr reCmd Status Data[] CRC-160x05 0xXX 0x2F 0x00 ----- LSB MSB8.4.7 Acousto-optic ControlThe host sends this command to control the LED lights flash and buzzer tweet.Command:Len Adr CmdData[]ActiveT SilentT TimesCRC-160x07 0xXX 0x33 0xXX 0xXX 0xXX LSB MSBParameter Connect:ActiveT: LED flash and buzzer tweet time. (ActiveT*50ms), the default value is 0.0
Page 1: UHF-RW-MP-232-V1 (RRU1861)User's Ma
Page 4 and 5: 3. DATA BLOCK FORMAT3.1 COMMAND DAT
Page 6 and 7: 3 Write Data 0x034 Write EPC 0x045
Page 8 and 9: This function is used to set a new
Page 11 and 12: 5 0xXX 0x0a 0x0e __ LSB+MSB5 0xXX 0
Page 13 and 14: 5 0xXX 0xXX 0xFD __ LSB+MSB5 0xXX 0
Page 15 and 16: user area in G2 tag of Inpinj Compa
Page 17 and 18: 0xXX Variable 0xXX 0xXX 0xXX 4Byte
Page 19 and 20: example, MaskAdr = 0x00 specifies t
Page 21 and 22: unwriteable, then later cannot chan
Page 23 and 24: memory. Other values reserved. Othe
Page 25 and 26: Respond:Len Adr reCmd Status Data[]
Page 27 and 28: 0x05 0xXX 0x0c 0x00 ----- LSB MSB8.
Page 29 and 30: 8.3.2 Inventory Multiple 6BThe comm
Page 31 and 32: 8.3.5 Check Lock 6BThe command is u
Page 33: 8.4.2 Set RegionThe host sends this
Page 37 and 38: Len Adr reCmd Status Data[] CRC-160
Page 39: Respond:Len Adr reCmd Status Data[]

UHF-RW-MP-232-V1 - RFID Shop

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?