Equipment/ functions - Process Valve Solutions

More documents

Recommendations

Info

24 Ambient conditions Enclosure protection IP 67 AUMA part-turn actuators conform to enclosure protection IP 67 according to EN 60 529. IP 67 means protection against immersion up to max. 1 m head of water for max. 30 minutes. Corrosion protection / Colour KN (standard) The standard AUMA corrosion protection KN is a high quality coating. This is suitable for outdoor installation and for slightly aggressive atmospheres with a low level of pollution. KS AUMA recommends this corrosion protection class when installing devices in occasionally or permanently aggressive atmospheres with a moderate pollutant concentration (e.g. in sewage treatment plants, chemical industry). KX AUMA recommends this corrosion protection class when installing devices in extremely aggressive atmospheres with high humidity and high pollutant concentration. Ambient temperatures IP 68 AUMA part-turn actuators are available with improved enclosure protection IP 68 according to EN 60 529. IP 68 means protection against submersion up to 6 m head of water for max. 72 hours. During submersion up to 10 operations are permissible. Aluminium-free version All outside parts including the handwheel are either made of cast iron, spheroidal cast iron or stainless steel. This actuator version is designed for use in atmospheres which are highly corrosive to aluminium. This includes atmospheres with high humidity and maritime climate such as those present onshore, offshore or in desalination plants. In order to guarantee the enclosure protection IP 68, suitable cable glands have to be used. They are not part of the standard supply, but can be provided by AUMA, if ordered. Colour The standard colour of the finish coating is silver-grey (DB 701, similar to RAL 9007). Other colour are possible on request. Versions SG SGR SGExC Standard – 25 °C – + 80 °C 1) – 25 °C – + 60 °C – 20 °C – + 40 °C 2) Low temperature – 40 °C – + 60 °C – 40 °C – + 60 °C – 40 °C – + 40 °C Extr. low temperature – 50 °C – + 60 °C – – 50 °C – + 40 °C High temperature 3) Versions SG SGR SGExC Standard – 25 °C – + 80 °C 1) – 25 °C – + 60 °C – 20 °C – + 40 °C 0 °C –+ 120 °C – – 2) Low temperature – 40 °C – + 60 °C – 40 °C – + 60 °C – 40 °C – + 40 °C Extr. low temperature – 50 °C – + 60 °C – – 50 °C – + 40 °C High temperature 3) 0 °C –+ 120 °C – – 1) With 3-phase AC motor up to + 80 °C, with 1-phase AC motor and/ or integrated RWG and/ or integral controls up to + 70 °C 2) In special sizing up to + 60 °C possible 3) Only possible with 3-phase AC motor
Explosion protection Lifetime Part-turn actuators for open-close duty SG/ SGExC One cycle is an operation from end position CLOSED to end position OPEN and vice versa for a swing angle of 90°. Type Cycles SG/ SGExC 05.1 20 000 SG/ SGExC 07.1 20 000 SG/ SGExC 10.1 15 000 SG/ SGExC 12.1 10 000 Mounting positions AUMA actuators (with or without integral controls) can be operated without restriction in any mounting position. For the installation of actuators in potentially hazardous or explosive areas, special protective measures are required. These are stipulated in the European Standards EN 50 014, 50 018 and 50 019. The PTB (Physikalisch Technische Bundesanstalt, the German national test authority) as European test authority certifies the conformity of the equipment with the mentioned standards. The explosion-proof versions of the AUMA SGExC correspond to protection class II2G EEx de IIC T4. Part-turn actuators for modulating duty SGR The lifetime in operation hours (h) depends on the load and the number of starts. A high starting frequency will rarely improve the modulating accuracy. To reach the longest possible maintenance and fault-free Type Starts in million. min. Ambient conditions Certificates of conformity from national test authorities in other countries, e.g. CIS are also available. For the current versions of the certificates refer to the Internet under: www.auma.com (download section). operation time, the number of starts per hour chosen should be as low as permissible for the process. This can be achieved by setting the modulating parameters accordingly. Number of starts per hour for an expected lifetime based on min. operation hours 1) 5.000 h 10 000 h 20 000 h Number of cycles max/h SGR 05.1 2,5 600 300 150 600 SGR 07.1 2,5 600 300 150 600 SGR 10.1 2,5 600 300 150 600 SGR 12.1 2,5 600 300 150 600 1) Based on the permissible torque for modulating duty according to ‘Technical Data SGR’ and the type of duty S4 - 25 % 25
Page 1 and 2: ISO 9001 ISO 14001 Certificate Regi
Page 3 and 4: AUMA part-turn actuators are employ
Page 5 and 6: ●Standard ■Option Equipment / f
Page 7 and 8: Modulating duty Input signal from p
Page 9 and 10: Adjustable torques Minimum and maxi
Page 11 and 12: Magnetic limit and torque transmitt
Page 13 and 14: Running indication (option) As an o
Page 15 and 16: Motor 9 An especially high starting
Page 17 and 18: Motor protection In order to protec
Page 19 and 20: Special connections For special cus
Page 21 and 22: Integral controls (option) with AUM
Page 23: Advantages of integral controls (op
Page 27 and 28: A Absolute encoder 11 Actor 4 Actua

Equipment/ functions - Process Valve Solutions

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?