EHD Manual - JS Woodhouse

More documents

Recommendations

Info

24Trouble Shooting GuideSymptom:Problem:SOLUTION:Elevator or conveyor tears hay loose from bottom side of bale.Elevator or conveyor tracks do not line up properly.Gently hammer tracks into alignment. Properly aligned tracks will not grab hay from bottom ofmoving bales.Tap corner down with hammerChainTravelTap corner down with hammerSymptom:Problem:SOLUTION:Bales travel over kick-off and down conveyor.Kick-off fin does not stay in up position.Secure kick-off with control rope (refer to illustration on page 18). When securing the kick-off, usethe control rope that is connected to the kick-off arm in the backward position. The side of thekick-off with the arm in the backward position is also the side of the kick-off with the fin in the upposition. Securing the backward arm holds the fin in the up position and prevents a hay bale frompushing the kick-off along toward the end of the conveyor.Bales should not be run over the top of the kick-off and back down into the conveyor. The kick-offlifts the conveyor chain out of the conveyor chain track. When the bale travels over the top of thekick-off and back down into the conveyor, it may push the chain off to the side of the conveyorchain track. The weight of the bale will hold the chain off to the side of the conveyor chain track,and as it reaches the end of the conveyor, it may be derailed from the drive sprocket.Symptom:Problem:SOLUTION:Symptom:Problem:SOLUTION:Bales are bunching up at the kick-off and not going over the side smoothly.Kick-off model does not match Conveyor model.Contact the factory for assistance in model identification.Bales travel up kick-off and wedge against the ceiling.Conveyor possibly hung too close toward ceiling.Lower the conveyor to increase ceiling clearance.11160412170
Trouble Shooting Guide25Symptom:Problem:Problem:Problem:Bales are bunching up at kick-off and not going over the side smoothly.Mow Conveyor is not setting level.Motor weight at drive end pulls one side of the conveyor down.Mow Hangers are not installed level.RightWrong(End View)(End View)SOLUTION:Clamp conveyor to a solid wood mow-hanger as shown below. Locate wood mow-hanger nearmotor drive end of conveyor, as weight imbalance (due to motor) is greatest at that point. Woodmow-hangers are not available from the factory.(End View)11160412170
Page 1 and 2: WARNINGEHDExtra-Heavy-Duty Bale Ele
Page 3 and 4: 1ForewordThis Manual is intended to
Page 5 and 6: The Decals Shown On This Page Must
Page 7 and 8: Maximum Angle of Elevationfor Vario
Page 9 and 10: Machine Inspection7Winch and CableW
Page 11 and 12: Movement and Placement9RightWrongLo
Page 13 and 14: Movement and Placement11MinimumDist
Page 15 and 16: New Lockout/Tagout Rule Becomes Eff
Page 17 and 18: 15Work Area Diagram - Movement and
Page 19 and 20: 17THIS PAGE LEFTINTENTIONALLYBLANK1
Page 21 and 22: Bale Kick-off Operation and Assembl
Page 23 and 24: Optional Accessories21Connector pla
Page 25: Trouble Shooting Guide23Symptom:Pro
Page 29 and 30: Trouble Shooting Guide27SOLUTION:Po
Page 32 and 33: 30OPERATING HEIGHTS & GENERAL DIMEN
Page 34 and 35: 32LAYOUT GUIDEBALE HANDLING SYSTEMS
Page 36 and 37: 34HAY CONVEYOR (Model EHD) - Parts
Page 38 and 39: 36Owner’sandOperator’sManualIll
Page 40 and 41: 38THIS PAGE LEFTINTENTIONALLYBLANK1
Page 42 and 43: 40Located idler shaft #39 , 3/8" nu
Page 44 and 45: 42Install lower shield #37 onto the
Page 46 and 47: 44Install shield cover #33 onto ele
Page 48 and 49: PLACEFIRST CLASSPOSTAGEHERET. R. Me
Page 50: WARNINGRead and Understand this man

EHD Manual - JS Woodhouse

Create successful ePaper yourself

Delete template?

Save as template?