Altivar 58 Telemecanique - error

More documents

Recommendations

Info

Drive MenuCode Description Adjustment range Factory settingPGt PG Type INC-DET DETDefines the type of sensor used when an encoder feedback I/O card is installed :INC : incremental encoder (A, A+, B, B+ are hard-wired)DET : detector (only A is hard-wired)PLS Num. Pulses 1 to 1024 11Defines the number of pulses for one rotation of the encoder.Parameters in gray boxes appear if an I/O extension card is installedENGLISH86
Control MenuThis menu can be accessed when the switch is in positionmode with the speed controller locked.. The parameters can only be modified in stopCode Description Adjustment range Factory settingtCC TermStripCon 2W- 3W (2-wire/ 3-wire) 2WConfiguration of terminal control : 2-wire or 3-wire control.Modification of this parameter requires double confirmation as it results in reassignment ofthe logic inputs. By changing from 2-wire control to 3-wire control, the logic input assignmentsare shifted by one input. The LI3 assignment in 2-wire control becomes the LI4 assignmentin 3-wire control. In 3-wire control, inputs LI1 and LI2 cannot be reassigned.I/O Handling General use Variable torqueLI1 STOP STOP STOPLI2 RUN forward RUN forward RUN forwardLI3 RUN reverse RUN reverse RUN reverseLI4 2 preset speeds jog operation ref. switchingLI5 4 preset speeds freewheel stop injection brakingLI6 8 preset speeds clear faults freewheel stopENGLISHThe I/O with a gray background can be accessed if an I/O extension card has been installed.3-wire control (pulse control : one pulse is sufficient to control start-up). This option inhibits the"automatic restart" function.Wiring example :LI1 : stopLI2 : forwardLIx : reverseATV<strong>58</strong> control terminals24 V LI1 LI2 LIxThis option only appears if 2-wire control is configured.Code Description Adjustment range Factory settingtCt Type 2 Wire LEL-TRN-PFo LELDefines 2-wire control :- according to the state of the logic inputs (LEL : 2-wire)- according to a change in state of the logic inputs (TRN : 2-wire trans.)- according to the state of the logic inputs with forward always having priority over reverse(PFo : Priorit. FW)Wiring example :LI1 : forwardLIx : reverseATV<strong>58</strong> control terminals24 V LI1 LIxParameters in gray boxes appear if an I/O extension card is installed87
Page 3: Altvar 58Terminal d’exploitation
Page 11: Access to MenusThe number of menus
Page 16 and 17: Display MenuDisplay menu (selection
Page 18 and 19: Adjust MenuThis menu can be accesse
Page 20 and 21: Adjust MenuThe following parameters
Page 22 and 23: Adjust MenuThe following parameters
Page 24 and 25: Adjust MenuENGLISHCode Description
Page 26 and 27: Drive MenuENGLISHCode Description A
Page 30 and 31: Control MenuCode Description Adjust
Page 32 and 33: I/O MenuThis menu can be accessed w
Page 34 and 35: I/O MenuENGLISHTable of the analogu
Page 36 and 37: ➞➞ ➞➞➞➞Configurable I/O
Page 38 and 39: Configurable I/O Application Functi
Page 48 and 49: Fault MenuCode Description Factory
Page 50 and 51: Files MenuFiles menu (continued)Cod
Page 52 and 53: MaintenanceENGLISHFault displayed P
Page 54 and 55: MaintenanceMalfunction with no faul
Page 56 and 57: Saving the Configuration and Settin
Page 58 and 59: Summary of MenusENGLISH3 - DRIVE me
Page 60 and 61: IndexENGLISHFunction Menus Pages+ /

Altivar 58 Telemecanique - error

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?