RF-SSKSite Survey Kit (SSK)THE SITE SURVEY KITIt is comprised of a receiver RF-RXSS which isused in conjunction with the <strong>Sontay</strong> RF-PS-500site survey routers, RF-HHT hand-held monitorand RF-TS-900 nodes. Routers are used toroute signals from battery powered nodes andother routers to the receiver module, wherethe signal strength of a direct path is notsufficient for reliable communications.DATA TRANSMITTIONData is transmitted back to the receiverat configurable time intervals, or on aconfigurable change in measured value.Each sensor retains these configurations ifthe battery becomes discharged or requiresreplacement.RF-SSK-HIREHire of the RF-SSK SonNet Site Survey Kit forsix working days - £133. See page 81 for fullhire terms and conditions.THE SSK RECEIVERAutomatically selects which of the 16 transmission channels available givesthe best radio network performance, taking into account both signalstrength and interference levels from adjacent channels and equipment(such as Wi-Fi etc.) The SSK hand-held monitor, nodes and routersautomatically find the best path back to the receiver, which may be directlyto the receiver or via “parent” routers.Part code DescriptionSite Survey KitRF-SSK Site Survey Kit (SSK) - containing:4 sensor nodes, 2 routers, receiver, hand-held monitorand power chargers for the rechargeable batteries(Individual units)RF-TS-900 Sensor End Device (rechargeable)RF-PS-500 Plant Router (rechargeable)RF-HHT Hand-held ToolRF-RXSS Site Survey RecieverData sheets: please contact our Customer Services Teamor visit www.sontay.com for datasheetsRF-RSBattery Powered Sensors (EDs)SonNet PARTSBattery Powered Sensors (EDs)Sensor nodes are used in conjunction withthe <strong>Sontay</strong> RF-RX20, RF-RX40 or RF-RXSreceiver units, and if required (depending oninstallation topography), <strong>Sontay</strong> RF-RR seriesof routers.Data is transmitted back to the receiverat configurable time intervals, or on aconfigurable change in measured value.Each sensor retains these configurations ifthe battery becomes discharged or requiresreplacement.The sensors automatically find the best pathback to the receiver, which may be directly tothe receiver or via ‘parent’ routers.Battery powered nodes are availablein four formats:■■Space mounting temperature,with setpoint and momentaryswitch options■■Space mounting RH&T,with setpoint and momentaryswitch options■■Plant mounting temperature■■Plant mounting RH&TSPECIFICATIONRadio Output: Frequency 2.4GHz, 16 channels,direct-sequence spread spectrumCompliance IEEE 802.15.4-2006Aerial Characteristics: Space Gain 1.2dBi, VSWR 1.5:1Plant Gain 2.0dBi, VSWR 2:1Data Encryption: AES 128Power Output:0dBmAccuracy: Temperature ±0.3°COptional RH ±3% RHBattery Type: Space 3.6V AA 2.4Ah Li-SOCl 2 ,non-rechargeablePlant 3.6V 2.1Ah 2/3 A Li-SOC l2 ,non-rechargeableBattery Life:>3 years (depending on configuration)Plant Sensor Types: Duct, outside air, outside air with solar radiationshield, immersion, strap-on and flying leadPart code DescriptionEnd Sensing DevicesRF-RS-T-911 Space Temperature Sensor *RF-RS-T-322 Duct Sensor - 150mm probeRF-RS-T-341 Immersion Sensor - 150mm probeRF-RS-T-351 Clamp-on SensorRF-RS-T-331 Outside Air SensorRF-RS-T-332 Outside Air Sensor c/w rad. sheildRF-RS-T-555-2 Flying Lead Sensor - 2mRF-RS-T-555-5 Flying Lead Sensor - 5mRF-RS-R-911 Space Humidity & temp. Sensor *RF-RS-R-622 Duct Humidity & temp. SensorRF-RS-R-631 Wall Humidity & temp. SensorRF-RS-R-632 Outside Humidity & temp. Sensor* Sensor Options for -911 only (add to part code)-MS Momentary switch interface * *-SPSet-point adjuster interface-MS-SP Momentary override & set-point * ** * The -MS switch option is ‘momentary’ in its physical action, but ‘latching’in its radio output. When the momentary switch is pressed, the currentoutput status is inverted (TRUE goes to FALSE or FALSE goes to TRUE) andstays in the new state until the switch is pressed again. Please allow for thisaction in the controller strategy to achieve the required control action.Data sheets: please contact our Customer Services Teamor visit www.sontay.com for datasheetsAir & Water Flow Air Quality & Gas Detection Controllers Input / Output Modules Water & Energy Metering Peripherals46www.sontay.com · Email sales@sontay.com
RF-RR24V Powered RoutersSonNet PARTS24V Powered RoutersThese routers are used in conjunction with the<strong>Sontay</strong> RF-RX20, RF-RX40 or RF-RXS receiverunits, and RF-RS series of battery poweredradio sensors, and are used to route signalsfrom battery powered nodes and other routersto the receiver module, where the signalstrength of a direct path is not sufficient forreliable communications.Note: Each router can support a maximum of 16 ‘children’, which can consistof a maximum of 8 battery powered nodes and 8 routers, or up to 16 routersif there are no battery powered nodes. Consideration should be given tonetwork planning for redundancy in case of router failure or damage.Routers automatically find the best path back to the receiver, which may bedirectly to the receiver or via other ‘parent’ routers.24V powered routers are available in five formats:■■Space mounting temperature, with setpoint & momentary switch options■■Space mounting RH&T, with setpoint and momentary switch options■■Plant mounting router, no sensor functions■■Plant mounting temperature■■Plant mounting RH&TSPECIFICATIONRadio Output: Frequency 2.4GHz, 16 channels,direct-sequence spread spectrumCompliance IEEE 802.15.4-2006Aerial Characteristics: Space Gain 1.2dBi, VSWR 1.5:1Plant Gain 2.0dBi, VSWR 2:1Data Encryption: AES 128Power Output:+10dBmAccuracy:Temperature ±0.3°C (0.54°F)Optional RH ±3% RHPower Supply:Plant Router Types:24Vac/dcDuct, outside air, outside air with solar radiationshield, immersion, strap-on and flying leadPart code DescriptionRoutersRF-RR-900 Router (space housing)RF-RR-300 Router (plant housing)Router SensorsRF-RR-T-911 Space Temp. Sensor/Router *RF-RR-T-322 Duct Sensor/Router - 150mm probeRF-RR-T-341 Router Immersion Sensor - 150mm probeRF-RR-T-351 Router Clamp-on SensorRF-RR-T-331 Router Outside Air SensorRF-RR-T-322 Router Outside Air Sensor c/w Rad ShieldRF-RR-T-555-2 Router Flying Lead Sensor - 2mRF-RR-T-555-5 Router Flying Lead Sensor - 5mRF-RR-R-911 Router Space Humidity & Temp. Sensor *RF-RR-R-622 Router Duct Humidity & Temp. SensorRF-RR-R-631 Router Wall Humidity & Temp. SensorRF-RR-R-632 Router Outside Humidity & Temp. Sensor* Sensor/Router Options for -911 only (add to part code)-MS Momentary switch interface * *-SPSet-point adjuster interface-MS-SP Momentary override & set-point * ** * The -MS switch option is ‘momentary’ in its physical action, but ‘latching’in its radio output. When the momentary switch is pressed, the currentoutput status is inverted (TRUE goes to FALSE or FALSE goes to TRUE) andstays in the new state until the switch is pressed again. Please allow for thisaction in the controller strategy to achieve the required control action.Data sheets: please contact our Customer Services Teamor visit www.sontay.com for datasheetsRF-RXSystem ReceiverSonNet PARTSSystem ReceiverThe <strong>Sontay</strong> RF-RX20 or RF-RX40 receivercollects data from all other devices on theradio network, including measurements fromsensors, link quality for all links formed in thenetwork, battery levels for all battery powereddevices, hours run for all devices and thecurrent status of all devices.Note: Each receiver can support a maximum of 16 ‘children’, which canconsist of a maximum of 12 battery powered nodes and 4 routers, or up to16 routers if there are no battery powered nodes.A USB socket is provided for connection to a PC or laptop running the<strong>Sontay</strong> SonNet CMS software.Receivers are available in two formats:■■RF-RX20 - 20 x 0-10Vdc analogue outputs■■RF-RX40 - 40 x 0-10Vdc analogue outputsFor a live demonstration of the SonNet Wireless Monitoring System pleasecontact the <strong>Sontay</strong> Sales Team at sonnet@sontay.com.Part codeRF-RX20RF-RX40DescriptionReceiver ModulesReceiver with 20 x 0-10Vdc outputsReceiver with 40 x 0-10Vdc outputsSPECIFICATIONRadio Output: Frequency 2.4GHz.16 channels,direct-sequence spread spectrumCompliance IEEE 802.15.4-2006Aerial Characteristics: Gain: 2.0dBiVSWR: 2:1Data Encryption: AES 128Power Output:+10dBmAnalogue Outputs: RF-RX20 20 x 0-10Vdc analogue outputs@10mA max. eachRF-RX40 40 x 0-10Vdc analogue outputs@10mA max. eachOutput ranges: Temp. –10 to +70°C (14 to 158°F)RH 0 to 100%Setpoint 0 to 100%Switch 0Vdc = OFF, 10Vdc = ONPower Supply:24Vac/dcHousing:DIN-rail, 203 x 104 x 38mm (W,H,D)(7.99 x 4.09 x 1.5”) – excluding aerialPart code DescriptionRF-AccessoriesRF-RSBattery for space sensorsRF-RPBattery for plant sensorsRF-AERIAL-PM2 Aerial extension c/w bulk head fitting- 2m (6.56 ft)Aerial extension c/w bulk head fittingRF-AERIAL-PM5- 5m (16.40 ft)Data sheets: please contact our Customer Services Teamor visit www.sontay.com for datasheets& Interfaces Pressure Relative Humidity Wireless Devices Temperature Valves & ActuatorsUK Tel. +44 (0) 1732 861200 · Int. Tel. +44 (0) 1732 861225 · UK Fax +44 (0) 1732 861201 · Int. Fax +44 (0) 1732 86122647