TorqueMaster Plus Standard Lift - Wayne Dalton

(2) 1/4”-20 x 11/16”Self drilling screws(2) 1/4”-14 x 5/8”Self tapping screws(2) 1/4”-14 x 5/8”Self tapping screws(2) 1/4”-20 x 11/16”Self drilling screwsStrut (A-symmetrical) End cap(attached to top rib)Lock section30” To 36”Left double graduatedend hinge with longstem track rollerRight double graduatedend hinge with longstem track roller12Verticaltracks1/4”-14 x 5/8” Self tapping screw locationsLeft graduated end hingewith short stem track rollerCenterhinge(s)Secure topmiddlehole firstRight graduated end hingewith short stem track rollerTop FixturesTools: Power drill, 7/16” Socket driver, Phillips screwdriverTo install the top fixtures, align the top holes in the top fixture base with the second set ofholes in the end cap of the top section. Fasten to section using (4) 1/4”-14 x 5/8” self tappingscrews. Secure the top fixture slide to the fixture base loosely using (2) 1/4”-20 x 5/8”carriage bolts and (2) 1/4”-20 flange hex nuts.Fasten (2) Quadrex Pan Head screws, one in the middle hole of the top fixture base and theother in the corresponding hole below the top fixture base.NOTE: If you have 7’0” door height, use (2) #8 x 1-13/32” quadrex pan head screws.NOTE: If you have 8’0” door height, use (2) #8 x 1-21/32” quadrex pan head screws.The top fixture slide will be tightened and adjusted later, in step, Adjusting Top Fixture. Insertshort stem track roller into top fixture slide. Repeat same process for other side.Top fixture slideShort stem track roller(4) 1/4”- 14 x 5/8”Self-tapping screws(2) Quadrex panhead screws13(2) 1/4”- 20 x 5/8”Carriage boltsTop sectionEnd cap2nd SetTop fixturebase(2) 1/4”- 20Flange hex nutsStrut (A-symmetrical)Tools: Power drill, 7/16” Socket driver, Tape measureEndcap hole pattern2nd SetNOTE: If an a-symmetrical strut is supplied, complete this step.Place the a-symmetrical strut over the top rib of the top door section. Fasten each end ofthe a-symmetrical strut to the end cap with (2) 1/4”-20 x 11/16” self drilling screws. Fastenboth wall and the long leg of the a-symmetrical strut, as shown using (2) 1/4”-14 x 5/8”self tapping screws every 30-36 inches. (Approximately 18 self tapping screws per 18’a-symmetrical strut)IMPORTANT: When securing the a-symmetrical strut to the top section, itis recommended not to install any fasteners into the short leg of the a-symmetrical strut.14Strut (A-symmetrical) side viewLong legShort legDrawbar Operator BracketTools: Power drill, 7/16” Socket driver, Flat head screwdriver, 7/16”Wrench, Tape measure, PencilImportant: when connecting a drawbar operator type garage door openerto this door, a Wayne-Dalton operator/ drawbar operator bracket mustbe securely attached to the top section of the door, along with any strutprovided with the door. The installation of the drawbar operator must be accordingto manufacturer’s instructions and force settings must be adjustedproperly.Position the drawbar operator bracket arm inside the top portion of the top half of drawbaroperator bracket and flush against the back of the top half of drawbar operator bracket.Adjust the top holes in the drawbar operator bracket arm with the two upper holes in the tophalf of drawbar operator bracket.Fasten both the drawbar operator bracket arm and the top half of drawbar operator brackettogether using (2) 1/4”-20 x 9/16” track bolts and (2) 1/4”-20 flange hex nuts.Slide the bottom half of drawbar operator bracket inside the top half of drawbar operatorbracket. Adjust the both the top and bottom halves of drawbar operator brackets out againstthe top and bottom rib of the top section. Loosely fasten both the top and bottom halves ofdrawbar operator brackets together using (4) 1/4”-20 x 9/16” track bolts and (4) 1/4”-20flange hex nuts.NOTE: Install the 1/4”-20 x 9/16” track bolts and the 1/4”-20 flange hex nuts as far apartas possible, when positioning both the top and bottom halves of drawbar operator bracketstogether.NOTE: For retro fit applications, the drawbar operator bracket assembly must be aligned withan existing drawbar operator.Now, locate the center of the top section and align the center of the holes in the drawbar operatorbracket assembly with the top section center line. Align the drawbar operator bracketassembly vertically.First, secure the back of the drawbar operator bracket assembly to the top section insidesurface using (2) 1/4”-20 x 11/16” self drilling screws. Next, secure the drawbar operatorbracket assembly to the top and bottom ribs of the top section using (8) 1/4”-20 x 11/16”self drilling screws. Now, tighten all previously installed 1/4”-20 x 9/16” track bolts and1/4”-20 flange hex nuts.Secure the drawbar operator bracket assembly to the top section using (1) quadrex pan headscrew.NOTE: If you have 7’0” door height and your door width is less than or equal to 16’0”, use (1)#8 x 1 21/32” quadrex pan head screw.NOTE: If you have 7’0” door height and your door width is greater than 16’0”, use (1) #8 x 113/32” quadrex pan head screw.NOTE: For door heights greater than 7’0”, use (1) #8 x 1 13/32” quadrex pan head screw.(2) 1/4”-20 x9/16” Track bolts Top riband (2) 1/4”–20 Flange hex nutsDrawbar operatorbracket armTop half of drawbaroperator bracketTop half of drawbaroperator bracket(4) 1/4”-20 x9/16” Track boltsand (4) 1/4”–20 Flange hex nutsBottom half of drawbaroperator bracketBottom ribTopsectioninsidesurface9Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer,refer to your local yellow pages business listings or go to the Find a Dealer section online at www.Wayne-Dalton.com