SIMPROP INTELLI CONT V3 Manual - Modellismo Fioroni

More documents

Recommendations

Info

(9) OPERATION and FINISH DISPLAY[SOLO-RUNNING] -> SOLO mode balance[SYNC-RUNNING] -> SYNC mode balance[ **COMPLETE** ] -> Balance completeConnected cell numberConnected Pack voltageConnected Pack TCSSelected cell numbercell voltageMODE[ BALANCER ] 16CL 00.000V 0%DOWNLiIo -> Lithium-ion batteryLiPo -> Lithium polymer batteryA123 -> Lithium Fe batteryMODE C 0000mAh 00.0Vi 100.00V 00.00A 00%MODEAUTO : AUTOMATICNORM : NORMALLINE: LINEARSOLO : SOLO MODESYNC : SYNC MODECcCv: CC-CVC01D : CYCLE MODESTOR : STORE MODEA123 SYNC 000:00 100.00A 0.000VUPA123 CHG 000:00 100.00A 0.000VDOWNENTERIf LONG UP button is pressed, eachparameter will display in 2-second rotation.Output currentOutput voltageENTER A123 CHG 000:00 100.00A 0.000VUPDOWNUPSELECT [0CL] 1VOLTAGE 00.000VDOWNUPAVG. V 00.000V 1GAP V 00.000VDOWNUP3 68 3.62 3.63V 13.62 3 70 3.62VQUICK VIEW DATA DISPLAYC : Charge or D : DischargemAh (charged in or discharged out)Vi Input (i) VoltageV Pack Voltage,A Charge Current% TCS capacity (Lithium types only.NiCd, NiMH, PB show --%)00.00A 0.000VCAPA. 00000mAhINPUT 00.000VTEMP 0.0`CPEAK.T 0.0`CPEAK.V 0.000VBAT. RES 000mΩTCS CAP. 000%FINISH…Capacity Units DisplayedNiMh, NiCd, LiPo, Liio, LiFePO4 = mAhPb = AhOutput current, Output voltageCharge capacityInput voltageBattery temperatureBattery peak temperatureBattery peak voltageBattery internal resistanceTCS capacityThe decimal point changes to squarebox to indicate a high cell which isbeing discharged to balanceA123 CHG 000:00 100.00A 0.000VCOMPLETE 100.00A 0.000VFinish status display"END:DELTA-PEAK ""COMPLETE"“END:CUTOFF-VOLT”"END:TEMPERATURE""END:CAPACITY ""END:TIMER ""END:TCS CAP. "[ MEMORY No.0 ] 1A123 9.9V 2300ENTER-2SEC
(10) LiIo / LiPo / LiFePO4 (a123) FINISH DISPLAYLiPo CHG 62:24 1+ 1.00A 8.103VLiPo SOLO 62:25 1+ 1.00A 8.103VCharge CC/CV & DischargeOperating DisplayLiPo CHG 65:32 1 LiPo BLC 65:32 1+ 1.00A 8.103V + 0.20A 8.103VClock continues to count time until BLC is finishedCurrent (if any) during BLC is shownLiPo CHG 68:40 1+ 0.00A 8.400VLiPo END 68:40 1+ 0.00A 8.400VEND time should show total of CC/CV and BLCphases(11) NiCd/NiMH CYCLE OPERATION DISPLAY[ MEMORY No.0 ]NiMh 7.2V 3300ENTERCYCLE STARTC>D 5T 10minENTER* * BATTERY * ** * CHECK * *NiMh C01D 00:01 1+ 4.00A 7.512VNiMh C01D 09:59 1+ 0.00A 8.720VNiMh C01D 09:59 1- 4.00A 8.713VEND:CUTOFF-VOLT 100.00A 0.000VNiMh C01D 09:59 1- 0.00A 6.618V5 Cycle repeat
Page 1 and 2: EOS0615i-DUO3 LAYOUT and OPERATION
Page 3 and 4: (2) MEMORY DISPLAY (settings availa
Page 5: (5) USER SETUP DISPLAYCH#1 Global S
Page 10 and 11: ERROR MESSAGESINPUT VOLTAGEERROR 0.

SIMPROP INTELLI CONT V3 Manual - Modellismo Fioroni

Create successful ePaper yourself

Delete template?

Save as template?