HAUCK LONG NOSE STARJET BURNER LNSJ360 â LNSJ980

More documents

Recommendations

Info

C. BURNER CAPACITIES (METRIC)Page 4LNSJ -9BurnerModelAir Flow(nm 3 /min)Pressure(kPa)TBA BlowerModelMotorHPFan Rating(am 3 /min @ 177°C)Max. Capacity(kW)SJ360 145 15.9 TBA - 36 - 75 75 1,150 20,000SJ520 196 15.5 TBA - 36 - 100 100 1,470 25,600SJ580 212 14.2 TBA - 36 - 100 100 1,820 31,700SJ750 266 16.4 TBA - 36 - 125 125 2,280 39,700SJ980 327 15.5 TBA - 36 - 150 150 3,430 52,900Table 2. Long Nose StarJet Burner Capacities with High Pressure Direct Drive BlowersMetric Capacity Table Notes:1. Oil capacities based on Lower Heating Value (LHV) of 36.17 MJ/ and viscosity of oil delivered at theburner of 1.8 x10 -5 m 2 /sec or lower.2. Gas capacities based on LHV of 36.96 MJ/nm 3 and 34.5 kPa manifold inlet pressure with a 20.7 kPadrop across manifold.3. Liquid propane capacities based on LHV of 23.83 MJ/ and 345 kPa above vapor pressure atinlet of LP burner control valve (butane and 50/50 propane/butane mixture capacities availableupon request).4. Burner capacities based on standard air density: sea level (760mm Hg) at 21°C. Correction factorsmust be applied for altitude/temperature variations; consult Hauck.5. Only 40% of air for combustion is passed through the burner. The remaining 60% of air forcombustion plus a minimum of 20% excess air must be induced by the dryer exhaust system ata negative 6.3mm wc at the burner/breeching ring.6. Horsepower rating is based on Hauck blower performance. Blowers of other manufacturers may beused, however, higher horsepower motors may be required as a result of lower efficiencies.7. "E", "F" & "G" Model burners can be accurately monitored for air flow by using the body pressure P1test point with an accurate kPa pressure gauge. Burners equipped with a blower inlet orifice can bemonitored for air flow using a draft gauge capable of reading negative 76mm wc. Readings can berelated to nm 3 /hr on corresponding burner charts.8. Burners equipped with a gas orifice meter can be accurately checked for gas flow by measuring thedifferential pressure across the orifice meter with a U-tube device capable of reading 0-500mm wc.Readings can be related to gas flow using corresponding Burner Performance Tables under gasorifice P (mm wc) and gas flow (m 3 /hr).
D. DIMENSIONSPage 5LNSJ -9Y5373(NOT TO SCALE)Figure 1. Overall Length Dimensions LNSJ360 – LNSJ980
Page 1 and 2: INSTRUCTIONSHAUCK LONG NOSE STARJET
Page 3: C. BURNER CAPACITIESRefer to burner
Page 7 and 8: D. DIMENSIONS (Continued)Page 7LNSJ
Page 9 and 10: D. DIMENSIONS (Continued)Page 9LNSJ
Page 11 and 12: F. BURNER MOUNTINGPage 11LNSJ -9X53
Page 13 and 14: H. NATURAL GAS FUEL PIPING SYSTEMPa
Page 15 and 16: 5. The piping from the gas regulato
Page 17 and 18: I. LIGHT FUEL OIL PIPING SYSTEMPage
Page 19 and 20: 13. High fire oil flow can be adjus
Page 21 and 22: Page 21LNSJ -9NOTEHauck recommends
Page 23 and 24: Page 23LNSJ -9Y7513(NOT TO SCALE)Fi
Page 25 and 26: Page 25LNSJ -9NOTE120V/60Hz power f
Page 27 and 28: Page 27LNSJ -9M. COMPRESSED AIR/OIL
Page 29 and 30: Page 29LNSJ -9COMPRESSED AIR/OIL AD
Page 32 and 33: N. LIQUID PROPANE (LP) FUEL PIPING
Page 34 and 35: Page 34LNSJ -9NOTELP manifold must
Page 36 and 37: Page 36LNSJ -9e. Adjust the backpre
Page 38 and 39: Page 38LNSJ -94. Remove the four bo
Page 40 and 41: Page 40LNSJ -9O. BURNER PILOT SYSTE
Page 42 and 43: Page 42LNSJ -93. The plant exhaust
Page 44 and 45: Table 8. Initial Burner Component S
Page 46 and 47: Page 46LNSJ -9Secondary Air Sleeve
Page 48 and 49: 5. Periodically check all safety eq
Page 50 and 51: Interpretation of Gas Readings.Page
Page 52: Page 4GJ73FEDRUM MIX PLANTTYPICAL S

HAUCK LONG NOSE STARJET BURNER LNSJ360 â LNSJ980

Create successful ePaper yourself

Delete template?

Save as template?

HAUCK LONG NOSE STARJET BURNER LNSJ360 â LNSJ980