EN / ACS850-04 (1.1 to 45 kW) Hardware Manual - VAE ProSys sro

More documents

Recommendations

Info

$\ATS\schemi\ATS con S3-S4-S5\Rm002101.dwg - VAE ProSys sro$

38Mechanical installation
39Planning the electrical installationWhat this chapter containsMotor selectionSupply connectionThis chapter contains the instructions that you must follow when selecting the motor,cables, protections, cable routing and way of operation for the drive. If therecommendations given by ABB are not followed, the drive may experienceproblems that the warranty does not cover.Note: The installation must always be designed and made according to applicablelocal laws and regulations. ABB does not assume any liability whatsoever for anyinstallation which breaches the local laws and/or other regulations.Select the (3-phase AC induction) motor according to the rating table in the chapterTechnical data. The table lists the typical motor power for each drive type.Only one permanent magnet synchronous motor can be connected to the inverteroutput. It is recommended to install a safety switch between the permanent magnetmotor and the drive output in order to isolate the motor from the drive duringmaintenance work on the drive.Use a fixed connection to the AC power line.WARNING! As the leakage current of the device typically exceeds 3.5 mA, a fixedinstallation is required according to IEC 61800-5-1.Supply disconnecting deviceInstall a hand-operated input disconnecting device (disconnecting means) betweenthe AC power source and the drive. The disconnecting device must be of a type thatcan be locked to the open position for installation and maintenance work.EuropeIf the drive is used in an application which must meet the European Union MachineryDirective according to standard EN 60204-1 Safety of Machinery, the disconnectingdevice must be one of the following types:• a switch-disconnector of utilization category AC-23B (EN 60947-3)• a disconnector that has an auxiliary contact that in all cases causes switchingdevices to break the load circuit before the opening of the main contacts of thedisconnector (EN 60947-3)Planning the electrical installation
Page 3: ACS850-04 Drive Modules1.1 to 45 kW
Page 6 and 7: 6Installation and maintenance workT
Page 9 and 10: 9Table of contentsSafety instructio
Page 12 and 13: 12Dimensions and weights . . . . .
Page 15 and 16: 15About this manualWhat this chapte
Page 17 and 18: 17Installation and commissioning fl
Page 19 and 20: 19Terms and abbreviationsTerm/Abbre
Page 21: 21Operation principle and hardware
Page 24 and 25: 24Power connections and control int
Page 26 and 27: 26Ordering informationFor a complet
Page 28 and 29: 28Main dimensions and free space re
Page 30 and 31: 30Air outletAir inletArrange the co
Page 32 and 33: 32Planning the cabinet assembly
Page 34 and 35: 34The box contains:• ACS850-04 dr
Page 36 and 37: 36Installation procedureDirect wall
Page 40 and 41: 40• a circuit breaker suitable fo
Page 42 and 43: 42Safe Torque OffThe drive supports
Page 44 and 45: 44Alternative power cable typesPowe
Page 46 and 47: 46Selecting the control cablesIt is
Page 48 and 49: 48Planning the electrical installat
Page 50 and 51: 5021453Electrical installation
Page 52 and 53: 52Power cable connectionPower cable
Page 54 and 55: 5411. With frame size C or D, cut s
Page 56 and 57: 56Power cable connection - frame si
Page 58 and 59: 58Power cable connection - frame si
Page 60 and 61: 60Each drive has an independent DC
Page 62 and 63: 62Connecting the control cablesCont
Page 64 and 65: 64DI6 (XDI:6) as a thermistor input
Page 66 and 67: 66Grounding and routing the control
Page 68 and 69: 68Electrical installation
Page 70 and 71: 70CheckThe supply (input power) vol
Page 72 and 73: 72HeatsinkThe heatsink fins pick up
Page 74 and 75: 74Fan replacement (Frames C and D)T
Page 76 and 77: 76Maintenance
Page 78 and 79: 78Drive typeACS850-04…Nominal rat
Page 80 and 81: 80Dimensions and weightsSee also ch
Page 82 and 83: 82AC input (supply) connectionVolta
Page 84 and 85: 84Digital inputs/outputs DIO1and DI
Page 86 and 87: 86Ambient conditionsInstallation si
Page 88 and 89:
88CE markingA CE mark is attached t
Page 90 and 91:
90UL markingSee the type designatio
Page 92 and 93:
92Installation guidelines• If an
Page 94 and 95:
94Selection tableDrive typeACS850-0
Page 96 and 97:
96Mounting proceduresJFI-A1• Remo
Page 98 and 99:
98JFI-0x (Frames A…D, category C2
Page 100 and 101:
100Motor typeRandom-wound ABBM2__,
Page 102 and 103:
102du/dt and common mode filtering
Page 104 and 105:
104• The braking energy must not
Page 106 and 107:
106Braking circuit commissioningFor
Page 108 and 109:
108Frame size ADimension drawings
Page 110 and 111:
110Frame size CDimension drawings
Page 112 and 113:
112Mains chokes (type CHK-0x)689069
Page 114 and 115:
114JFI-B1Dimension drawings
Page 116 and 117:
116ParameterJFI-xx dimensionsFilter
Page 118 and 119:
118ParameterJBR-xx dimensionsResist
Page 120:
3AUA0000045496 REV D ENEFFECTIVE: 2
show all

EN / ACS850-04 (1.1 to 45 kW) Hardware Manual - VAE ProSys sro

Create successful ePaper yourself

Delete template?

Save as template?