NIBE F1330 - Klimats24.lv

More documents

Recommendations

Info

Installation / AdjustmentElectrical connectionConnection A heat pump must not be connected without the permissionof the electricity supplier and must be connectedunder the supervision of a qualified electrician. If an miniature circuit-breaker is used this should havea motor characteristic D (compressor operation). ForMCB size see Technical Specifications. When the building is equipped with an earth-faultbreaker, the heat pump should be equipped with aseparate one The F1330 does not include an isolator switch on theincoming electrical supply. The installation must be precededby a circuit-breaker with at least a 3 mm breakinggap. If an insulation test is to be carried out in the building,disconnect the heat pump.Sensor cables Connect the heat pump to the terminal block X9, 400V 3-phase, neutral + earth via a distribution board withfuses. Where there is more than one heat pump, eachunit must have a separate supply. Continue the installation by carrying out the inspectionset out in Description of functions - Start up >Inspection. NOTE! It is not permitted to fit additional componentsin the electrical connection area. Note that F1330 provides 230V control signals thatare intended to control external contactors andnot to drive pumps.164X9, incoming electricity Supply cableLEKThe heat pump in the picture is fitted with accessories.Phase sequence monitorF1330- 30, 40, 60 kWThe phase sequence monitor starts as soon as the powersupply is connected to the heat pump. Check the phasesequence as shown below. Orange LED is lit at correct phase sequence. Green LED is lit when there is power. If there is a fault in the phase sequence, the heat pumptriggers a brine alarm in both modules.16 NIBE F1330
Installation / AdjustmentDescription of functions - Start upDescription of functions - Start upInspectionThis inspection should be done on all heat pumps in thesystem individually. Other heat pumps should be switchedoff when the inspection is made.When F1330 is switched off during the inspection, theService mode should be reselected from menu 8.1.1 togain access to menus that are not normally accessible.NOTE!F1330-60 must be powered and the switchin position 1 for at least 12 hours before thecompressors can be started. This is because thecompressor oil must reach the correct operatingtemperature.If these instructions are not followed there is arisk of seriously damaging the compressors, thisapplies upon first-start up.1. Start the heat pump by turning the power switch (8)to the 1 position. The unit will now enter screen savermode and the text Master will be shown on the bottomrow of the display. When only Connecting flashesthe heat pump this may be because the heat pump isset as a Slave. If so, set the unit as the Master accordingto the instructions in Description of Functions –Start up > Master/Slave.2. Deactivate the screen saver by holding down the buttonin the far left corner and the enter button for approximately8 seconds. (See the section the Descriptionof Functions – Start up > Screensaver.)3. Set in the Service position from menu 8.1.1. (See theexample in Control > Changing parameters.)4. On delivery F1330 is set with English as the menulanguage, if another language is required this can bechanged in the menu 8.1.2.X95. Start the brine pump (KBP) by setting Continuous inmenu 5.4.6. See the section Description of functions -Basic functions > Brine pump.6. Check that the direction of rotation of the brine pumpagrees with the arrow on the pump. When the directionof rotation is wrong, two of the incoming phaseson terminal block X9 must be switched.7. Start the heating medium pump A (VBP-A) and theheating medium pump B (VBP-B) by setting Continuousin menu 5.4.7 and 5.4.8. See the section Description offunctions - Basic functions > Heating medium pumps.8. Check that the brine and heating medium pumps arevented and if necessary help the pumps to start.9. Go to menu 5.2.2 and check that the temperatures correspondwith the collector temperature, which indicatesthe brine flow.10. Short the inputs KPRAA and KPRAB with their ownstrap.+EBV-card+Measure cardJ5X4LEKThe heat pump in the picture is fitted with accessories.NIBE F133017
Page 1: LEKMOS GB 0909-1F1330031385INSTALLA
Page 10 and 11: User guide8 NIBE F1330
Page 13 and 14: A BA B5 0 . 0 ° CVa r m v a t t e
Page 17: Installation / AdjustmentElectrical
Page 21 and 22: Installation / AdjustmentDescriptio
Page 51 and 52: ControlControlControlGeneralThe men
Page 53 and 54: ControlControlMenu tree0.0 System [
Page 55 and 56: ControlControl6.0 External units* [
Page 57 and 58: ControlControlMain menus[N]S y s t
Page 59 and 60: ControlControlMenu 1.9.0 Hot water
Page 61 and 62: Control4.0 Outdoor temperatureMenu
Page 63 and 64: Control6.0 External units** Only sh
Page 65 and 66: ControlMenu 6.5.5 Max compr. to poo
Page 67 and 68: ControlMenu 7.4.0 Temp set back tim
Page 69 and 70:
ControlMenu 9.1.12 Hot water with a
Page 71 and 72:
LEKControlTechnical dataF1330-22100
Page 73 and 74:
MiscellaneousTechnical dataList of
Page 75 and 76:
LEKLEKLEKAJArtikel 018764ÖvrigtTec
Page 77 and 78:
MiscellaneousActions with operating
Page 79 and 80:
MiscellaneousActions with operating
Page 81 and 82:
MiscellaneousNIBE F133079
Page 83 and 84:
MiscellaneousNIBE F133081
show all

NIBE F1330 - Klimats24.lv

Create successful ePaper yourself

Delete template?

Save as template?