AquaMatic Series A100 Stager Control - Pentair Residential Filtration

More documents

Recommendations

Info

3 MIN/PINCYCLE TIME PROGRAMMINGSeries A100Each stager is configured with multiple positions. It is important toreview the product document that comes with the stager to determinethe number of positions.NOTE: The number of pins in the UP position on the pinwheel mustequal exactly the number of positions of the stager. Totalregeneration time cannot exceed 102 minutes.1. Remove the thumbscrew from the mounting bracket of the timerand swing the timer to the left.2. Pull up on the first pin (Start Cycle #1) of the pinwheel to mark thestart of the regeneration sequence (Figure 1).3. Use the PIN TIME CHART below, to determine the number of pinsto be left in the DOWN position. The number of pins left in theDOWN position represent the duration of the cycle (each pinequals approximately 3 minutes).4. Pull up the pin that represents start of the next cycle (Start Cycle#2) and repeat step 3 to determine the duration of this cycle.5. Repeat steps 3 and 4 as needed for the remainder of steps in theregeneration process. The last pin that is left in the UP positionwill send the controller back into the Service position.6. Return the timer to the proper mounting position and secure itusing the thumbscrew provided. Ensure that all electrical wiresare located away from the bottom of the timer.Pin Time ChartNumber ofNumber ofTime (Min.)Pins DOWNPins DOWNTime (Min.)0 3 17 541 6 18 572 9 19 603 12 20 634 15 21 665 18 22 696 21 23 727 24 24 758 27 25 789 30 26 8110 33 27 8411 36 28 8712 39 29 9013 42 30 9314 45 31 9615 48 32 9916 51 33 102Start cycle #3Cycle #3 = 9 minReturn to service72846096483602412Service notchPin upPin downFigure 1Cycle #2 = 45 minStart cycle #2Cycle #1 = 15 minStart cycle #1(First pin)2
SETTING A100 REGENERATION FREQUENCYSetting Days:1. Pull all skipper pins outward away from dial face (see Figure 2).2. Rotate skipper wheel until Day Arrow is aligned with either thecurrent day (for the 7 day wheel) or the number 1 (for the 6 daywheel).3. Depress skipper pin(s) at day(s) a regeneration is desired.6 PM3 PMNOON9 AM6 AMTimer knobSetting Time of Day:1. Grasp timer knob and pull outward.2. Rotate in either direction until actual time of day is aligned withTime Arrow.3. Release timer knob.NOTE: With the time of day properly set, the controller willregenerate at approximately 2:30 AM. If you prefer to have theunit regenerate at an earlier or later time, set the current timeof day accordingly. A label has been provided so that you canapply it to indicate the correct time of day.EXAMPLE: To set the unit to regenerate at 4:30 AM (2 hours later),set the clock 2 hours earlier than the actual current time.Position the label provided on the 24 hour dial whilealigning the mark of the current time with the Time Arrow.Press the label in place.Skipper wheelSkipper pinDay arrowMONTUESUNWEDSATTHUFRIPM3 AMMIDNIGHTSTARTSERVICEDAYFigure 2 A100 Timer Faceplate24-hour dialTime arrowPointer knobSERIES A100 STANDARD WIRING DIAGRAMLinePower SupplyNeutral21Timer4MotorMWhiteAquamatic Stager3C.UpperTimerSwitchN. O.N.C.Red(Run)Orange(Start)N.O . C.N.C.BlackIndexSwitchMotorMBlackWhite(Neutral)6C. N. O.LowerTimerSwitchN. C .Blue109BlueC. N. O.1st Aux.Switch N.C.(Homing - Shown In Service)VioletYellow785Output During Timer RegenerationFigure 33
Page 1: AquaMatic SeriesA100 Stager Control

AquaMatic Series A100 Stager Control - Pentair Residential Filtration

Create successful ePaper yourself

Delete template?

Save as template?