4040 - Methane / Nonmethane analyzer - Teledyne Analytical ...

More documents

Recommendations

Info

Installation Series 4040Regardless of configuration, the analyzer/system must be installedon a level surface with sufficient space allocated on either side forpersonnel and test equipment access. Subject to the foregoing, theAnalyzer/system should be placed as close to the sample point as ispossible.All pertinent dimensions, connecting points, and piping details canbe found in the drawings section as part of the outline, input-output, andpiping diagrams. These drawings are specific to the instrument orsystem to which the manual applies.3.3 User ConnectionsAll user connections are made on the rear panel. Consult the inputoutputand outline diagrams in the drawing section of the manual. Notall the features displayed may be present in your system. Refer to anyAddenda for additional information that may apply to your instrument.3.3.1 Electrical Power ConnectionsThe standard analyzer requires a supply of 100-125VAC, singlephasepower. Power connections are made at the rear panel of the unit.Refer to the input-output diagram for more information. The electricalpower service must include a high-quality ground wire. A high-qualityground wire is a wire that has zero potential difference when measuredto the power line neutral. If you have the 220 VAC option, you willrequire 220 or 240 VAC, 50/60 Hz power. Check the analyzer inputoutputdiagram, power schematic, outline, and wiring diagrams forincoming power specifications and connecting points.CAUTION:PRIMARY POWER TO THE SYSTEM SHOULD NOTBE SUPPLIED UNTIL ALL CUSTOMERS WIRING ISINSPECTED PROPERLY BY START-UP PERSONNEL.26 Teledyne Analytical Instruments
Installation3.3.2 Gas ConnectionsThe analyzer gas connection diagram identifies the various gasconnection points as to function and location. Figure 3-1 shows the gasconnection points for instruments with AutoCal module.SPAN GASFLOW RESTRICTOROPTIONALSAMPLE-SPANMANIFOLDFigure 3-1: Gas ConnectionsGas connections to the instrument are made at the 1/8”or 1/4”stainless steel tube fittings provided on the rear panel. Note that thePurge and Sensor Vent fittings are 1/4” while all other gas connectionsare 1/8”.It is recommended that all gas tubing leading to the connections onthe back of the analyzer be of the coiled type. This will facilitate slidingthe unit out of the case without disconnecting the gas supply to theanalyzer.Before tubing is connected to the system, it must be decontaminatedto rid it of hydrocarbon deposits. Using a small torch, heat each lengthof tubing, while passing nitrogen through it, until it glows red. Begin atthe nitrogen source end and proceed down the length of the tube,“chasing” the red glow (and hydrocarbon deposits) down to the openend of the tube. Cap tubing while not in use with suitable noncontaminatingcaps.Teledyne Analytical Instruments 27
Page 9 and 10: Table of ContentsSafety Messages ..
Page 11 and 12: 4.5.2 Expanded menus 494.6 Setting
Page 13 and 14: List of TablesTable 3-1: Analog Out
Page 15 and 16: IntroductionIntroductionTeledyne An
Page 17 and 18: Operational Theory Series 4040Opera
Page 19 and 20: Operational Theory Series 4040SENSO
Page 21 and 22: Operational Theory Series 4040The a
Page 23 and 24: Operational Theory Series 4040If au
Page 25: InstallationInstallationInstallatio
Page 29 and 30: Installation3.3.3.1 PRIMARY INPUT P
Page 31 and 32: InstallationThreshold Alarm 2:Can b
Page 33 and 34: Installation3.3.3.7 RANGE ID RELAYS
Page 35 and 36: Installation3.3.4 RS-232 PortThe di
Page 37 and 38: Installation3.3.5.2 EFFLUENTAll the
Page 39 and 40: InstallationFigure 3-3: Front Panel
Page 41 and 42: InstallationTeledyne Analytical Ins
Page 43 and 44: OperationOperation4.1 Analyzer Oper
Page 45 and 46: OperationScreen Modes:Screen Readou
Page 47 and 48: Operation5. When the selected optio
Page 49 and 50: Operation12. TIMING: Low level appl
Page 51 and 52: OperationDAC A - GOODDAC B - GOOD--
Page 53 and 54: Operation-----------------------STA
Page 55 and 56: OperationNote however, that the ins
Page 57 and 58: OperationReenter a new Password'A'
Page 59 and 60: Operation Start the diagnostic test
Page 61 and 62: Operationconcentration. If an activ
Page 63 and 64: OperationRANGE LIMITS: Ranges may b
Page 65 and 66: OperationTo exit STANDBY, scroll ag
Page 67 and 68: AppendixAppendixA.1 Specifications
Page 69: AppendixSend orders to:TELEDYNE INS

4040 - Methane / Nonmethane analyzer - Teledyne Analytical ...

Create successful ePaper yourself

Delete template?

Save as template?