Wadkin C5 C6 C7 C8 C9 Bandsaw Manual and Parts List

More documents

Recommendations

Info

18MITRE FENCEwww.wadkin.comFIG 21 ..STOP RODinfo@wadkin.comSTOP'RODSi---I---------M-ITRE-FENeE------------------I---FIG 22
· ; ,19RIP FENCE (EXTllA).A rigid rip fence FIG.20, is mounted on a round slide bar fitted to edge. of table.This fence can be mounted to rip either to inside or outBide of bandeaw blade.MITRE FENCE (EXTRA, SUPPLIED WIT!{ MACHINE :BY SPECIAL ORBIm).The mitre fance "A" in FIG.21. slides in the table slot. Two stop rode ":8" areheld together by two clamps "H" and wingnuts "C". The stop rode are secured tofence body by thUmbscrew liD".mlnl: Always ensure the s.top rode are set clear of the sawblade or. serious damagewill result when maohine is operated.The mitre fence can be rotated through 90 0 with positive stops. at 90 0 and 45 0 •To positi-on mitre fence at required angle, loosen handwheel "E" in FIG.21, thanpull plunger "F" from location, position fence as required using scale "G" thenrelook handwheel "E".mlnll Always ensure table slot is clear when using mitre if'ence.MITRE FENCE STOP RODS. (EXTRA)Accurate repetitive cutting can be made using the stop rode, see FIG.22.The rode are held in the fence by the thumbscrew "D" in FIG.21, and the stop rodeheld together by the two clamps "H".To adjust the rode by the clamps, loosen the wingnuts tIC".STARTING - STOPING.Start and Stop buttons are situated on the column of machine as shown in FI(h23.FOOTBRAKE (EXTllA).A footbrake is situated in the base of the machine as shown in FIG.24.mlnl: Always press "STOP" button before depressing footbrake.www.wadkin.cominfo@wadkin.com
Page 1 and 2: POWER BAND RIPSAWMODEL "C" RANGEwww
Page 3 and 4: Modifications are made to these boo
Page 5 and 6: 3INDEX (Cont'd)Belt Tension Adjustm
Page 7 and 8: 5SAFETY1. Read Instruction Book.2.
Page 9 and 10: 7:BANDSAW SLINGING INSTRUCTUIOllS.T
Page 11 and 12: 9FIG 1 FIG 2FIG 3 FIG 4www.wadkin.c
Page 13 and 14: 11FIG 6 FIG 7FIG 8 FIG 9www.wadkin.
Page 15 and 16: 13TENSIONING SAWBLADE USING SCALE (
Page 17 and 18: 15FIG 13Correct1 "I+- i'64 tI Rear
Page 19: 17~.The table cants to ·the right.
Page 23 and 24: 21FIG 25www.wadkin.cominfo@wadkin.c
Page 25 and 26: 23BELT TENSION.Incorrect tension is
Page 27 and 28: SAWDUSTDEFLECTOR.When machine is op
Page 29 and 30: 27AMOUNT OF TOOTH SETOVER SHOWN SHA
Page 31 and 32: 2'9GENERAL CAUSE:3 OF SAW TROUBLE.1
Page 33 and 34: HINTS ON. Cll'l"l'ING.311. Watch Fe
Page 35 and 36: 35www.wadkin.comWHEELS AND BELTinfo
Page 37 and 38: 33A7www.wadkin.comBASE, TOP COVER A
Page 39 and 40: TABLE ASSEMBLY.www.wadkin.cominfo@w
Page 41 and 42: 39MOTOR MOUNTING ASSEMBLY.www.wadki
Page 43 and 44: 41TOP SAWGUARD ASSEMBLY.www.wadkin.
Page 45 and 46: 43UNDER TABLE GUARD ASSEMBLY.www.wa
Page 47 and 48: 45.TABLE MOUNTING BRACKET ON BASE.
Page 49 and 50: 47BOTTOM SPINDLE ASSEMBLY.www.wadki
Page 51 and 52: 49TOP SPINDLE ASSEMBLY.www.wadkin.c
Page 53 and 54: 51www.wadkin.comTOP SLIDE ASSEMBLY.
Page 55 and 56: 53lTOP GUIDE ASSEMBLY .www.wadkin.c
Page 57 and 58: 55BOTTOM GUIDE ASSEMBLY.www.wadkin.
Page 59 and 60: 58BRAKE ASSEMBLY (EXTRA l.lIEF NO.
Page 61 and 62: 60SAW~SION INDICATOR ASSEMBLY (EXTR
Page 63 and 64: 62DELUX TOP SAWGUARll (EXTRA)REF.NO
Page 65 and 66: 64RIPmllE MlSmMIlLY (EXTt!A):REF.NO
Page 67 and 68: 66EXTENSION TABLE ASSEMBLY.Ref No.
Page 69 and 70: WHEELS AND BELT ASSEMBLY.Ref .No. P
Page 71 and 72:
ApplicationApproved LubricantCastro
Page 73 and 74:
72. WER,.. '·.0- F t'ITROLLERBEDEN
Page 75 and 76:
FfG 1 FIG 2www.wadkin.comFiG 3 FIG
Page 77 and 78:
nFI'l'l'lNG OF RIP SAW BLADES. (See
Page 79 and 80:
79SEll'TING SAW GUJJlESThe top and
Page 81 and 82:
81FEEDER UNIT. Fig 17.The feeder un
show all

Wadkin C5 C6 C7 C8 C9 Bandsaw Manual and Parts List

Create successful ePaper yourself

Delete template?

Save as template?