Viking Installation Guide Built-in Electric Warming Drawers (Indoor ...

CABINET CUTOUTINDOOR MODELS (VEWD, DEWD)CabinetModel VEWD173 VEWD103 VEWD163DEWD171 DEWD101A 25 1/4” 28 1/4” 34”(64.1 cm) (71.8 cm) (86.4 cm)23 3/8”(59.4 cm)ACavity Assy.9 1/4”(23.5 cm)DrawerAssy.Mounting Screws(4) - #8 x 3/4”OUTDOOR MODELSCabinet2” (5.1 cm)min.23 3/8”(59.4 cm)A9 1/4”(23.5 cm)Cavity Assy.Seal all around openingwith silicon caulk that isprovided.Model VEWD173T VEWD103T VEWD163TA 25 1/4” 28 1/4” 34”(64.1 cm) (71.8 cm) (86.4 cm)DrawerAssy.3

CABINET CUTOUTDFWD MODELSCabinetModel DFWD171 DFWD10125 1/4” 28 1/4”A (64.1 cm) (71.8 cm)24”(61.0 cm)Mounting Screws(4) - #8 x 3/4”Cavity Assy.(6) - #8 x 3/4” screws toattach custom front9 5/8”(24.4 cm)insulationcustom frontCUSTOM FRONT INSTALLATION - DFWD MODELS•Open the drawer and remove the pan.•Center the custom front and insulation around the inside panel.*NOTE: Make sure the insulation provided is used between the custom panel and the inside door panel.•Attach the custom front with the (6) six #8 x 3/4” screws provided.CABINET INSTALLATION•To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right and leftside until you reach the black hand latches (located at the front of the rails). Pull up on both the right and left latchesand pull drawer pan support completely out.•For outdoor models ONLY - Apply silicon caulk that is provided all around the back of the warming drawer trim.•Slide cavity assembly into cabinet opening.•Drill (4) pilot holes in cabinet using 1/8” drill bit. Permanently secure the warming drawer using the (4) #8 mountingscrews provided.•Replace drawer assembly.4

FRONTVEWDB10”(25.4 cm)FRONTDEWDB10”(25.4 cm)BFRONTDFWD3/4” thick10 1/2”(26.7 cm)REARC120V Electrical opening8 31/32”(22.8 cm)2”(5.1 cm)(When facing cabinet, opening islocated on right side.)2” (5.1 cm)MODEL VEWD173 DFWD171 VEWD103 DFWD101 VEWD163VEWD173T VEWD103T VEWD163TDEWD171DEWD101B 26 1/2” 26” 29 1/2” 29” 35 1/4”(67.3 cm) (66.0 cm) (74.9 cm) (73.7 cm) (89.5 cm)C 24 7/8” 24 7/8” 27 7/8” 27 7/8” 33 5/8”(63.2 cm) (63.2 cm) (70.8 cm) (70.8 cm) (85.4 cm)5

SIDEVEWD26 3/4” (67.9 cm)1 3/8” (3.5 cm)23 1/4” (59.1 cm) 25 3/4” (65.4 cm)SIDEDEWD26 3/4” (67.9 cm)1 3/8” (3.5 cm)23 1/4” (59.1 cm) 26 1/4” (66.7 cm)SIDEDFWD23 1/4” (58.7 cm)23 1/4” (58.7 cm)6

WIRING DIAGRAMBUILT-IN ELECTRIC WARMING DRAWERELEMENTPJ010008 - 36”PJ010009 - 30”PJ010010 - 27”FOR CONNECTION TO THE FACTORYINSTALLED TERMINAL BLOCK, USEALUMINUM OR COPPERCONDUCTORSINDICATOR LIGHTPE050024WARNING: TO REDUCE THE RISK OFELECTRIC SHOCK AND FIRE, DO NOTUSE A FLEXIBLE POWER-SUPPLY CORDWITH THIS APPLIANCE.WHITE 15”RED 6” RED 10”WHITE 10”BLACK 15”GROUNDGREEN/YELLOW 6”TERMINAL BLOCKPE070147THERMOSTATPB10167NEUTRALGROUNDLINEPOWER SUPPLYCONNECTIONSBY INSTALLERWARNING:FOR OUTDOORUNITS -INSTALLERMUST SUPPLYGFC INTERRUPT7

Viking Range Corporation111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For more product information,call 1-888-VIKING1 (845-4641) orvisit the Viking web sitewww.vikingrange.comF1615L(PS0206VR)