(Model CBDF) - Catalog 360 - Aerovent

More documents

Recommendations

Info

AccessoriesMotor CoverThe fiberglass motor cover extends over the entire base, motorand drive assembly to protect personnel from the moving driveparts and to protect the motor from precipitation.Housing DrainA 1" PVC pipe with a female pipe thread is located in thehousing to permit drainage of liquid. For horizontal applicationsonly.Horizontal Support LegsSupport legs are available for standard platform or floor mountingand are bolted to the inlet and outlet flange. The supportlegs are constructed of steel and coated with gray epoxy paint.Inlet and Outlet Screen304 or 316 Stainless SteelScreens offer protection to personnel from the fan’s movingparts and are recommended for use when no ductwork isattached to the inlet and/or outlet. Inlet and outlet screens areconstructed of expanded metal in 304 or 316 stainless steel.Bolted Inspection DoorThe bolted inspection door is recommended to inspect theinternal parts of the fan.ModificationsSpecial Fiberglass MaterialsPlease contact the factory to ensure a suitable material is selected for the specific application.• Vinyl Ester — Provides increased corrosion resistance to stronger acids, chlorine, and oxidizing agents. For use in industrial applicationssuch as chemical and water treatment plants, and commercial applications where urban or salt-air corrosion exists.• Surface Veil — Produces a smooth, reinforced final surface with greater corrosion resistance and protection from ultraviolet rays.• Fire-Retardant Resin — Reduces the resin’s tendency to burn by achieving a flame-spread rating of 25 or less.Spark Resistant ConstructionSpark resistant construction for fiberglass fans is recommended when the fan is handling explosive fumes. Although fiberglass is anon-sparking material, it can build and retain a static charge that can be potentially hazardous. With spark resistant construction, thefan is statically grounded by graphite impregnation to reduce a static charge build-up.Exterior 316 Stainless Steel HardwareExterior 316 stainless steel hardware is recommended when the environment outside the airstream is corrosive.4 Aerovent Bulletin 360
Roof Ventilator Design & ConstructionFor roof mounted exhaust applications, the Fiberglass CBDFInline Centrifugal Fan can be converted into a roof ventilatorwith the addition of a fiberglass stack cap, curb base, and motorcover. See page 10 for dimensional data.Note: When selecting performances from the rating tablesfor the roof ventilator design (with stack cap), allow 1 ∕8" forstack cap loss. A minimum flow rate is required to fully openthe stack cap damper blades. Please refer to the chart below.Design FeaturesStack Caps — Designed with backdraft dampers that protectthe interior of the building from precipitation when the fan isshut off.Minimum outlet velocity of 1700 FPMrequired for full open damper operation.Maximum outlet velocity not to exceed 3000 FPM.Design AdvantagesThe Fiberglass CBDF Roof Ventilator design:• Offers a quiet and efficient roof ventilator• Offers a long service life for fume exhaust applications• Permits fumes to be exhausted high above the roof line andaway from surrounding ventilation systemsConstruction Features• The stack cap windband section is constructed from a onepiecemold with drain channels and drain holes to allowwater to flow out.• The stack cap damper blades are reinforced with a turneddownflange at the blade edge that seals the fan dischargewhen the fan is shut off.• The stack cap damper rods are constructed of fiberglass withPVC bearings to offer a long service life.• The curb base is constructed from a one-piece mold thatoffers a no-seam base, thus eliminating the chance of waterleakage.• The curb base is reinforced to offer additional support for along service life.Curb Bases — Designed for mounting vertical fans on roofcurbs and to provide easy installation of the unit.Motor Covers — Designed to protect the motor and driveparts from the weather and to dissipate motor heat throughthe vents.Minimum CFM (m 3 /s) ValuesThe following table shows the minimum CFM (m 3 /s) requiredto fully open the fiberglass damper blades.MINIMUM VOLUMEFAN SIZE CFM m 3 /s(ENGLISH)(METRIC)12 2700 1.27416 4700 2.21820 7600 3.58725 15000 7.08032 19600 9.25139 29500 13.9245 Aerovent Bulletin 360
Page 1 and 2: ®The Industrial Choice.FIBERGLASS
Page 3: Corrosion Resistance GuideThe follo
Page 7 and 8: Performance DataSize 12 CBDF Outlet
Page 9 and 10: Size 32 CBDFOutlet Area = 12.80 Sq.
Page 11 and 12: Typical SpecificationsModel CBDF Be

(Model CBDF) - Catalog 360 - Aerovent

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?