class Continuum and Line Analysis Single-dish Software - IRAM

More documents

Recommendations

Info

10 CHAPTER 2. COOKBOOK 15. Delete output file if it exists. 16. Open the output file as new. 17-21 Make a loop over the index to substract the baseline and write the result. 22-25 Display the result from the output file. 2.7 Reading/Writing FITS file 2.7.1 Exporting class Spectra through FITS 1 set angle sec 2 file in co21.30m 3 find /range -2 2 -2 2 4 get f 5 set fits mode spectrum 6 fits write single.fits 7 find /range -2 2 -2 2 8 fits write index.fits /mode index 1. Angles are expressed in arcseconds. 2. Open the .30m file. 3. Build the index. 4. Store the first spectrum in R memory. 5. Default mode for writing FITS is set to single spectrum. 6. Write the R memory in FITS format file ’single.fits’. 7. Re-build the index. 8. Write the whole index in FITS format file ’index.fits’. 2.7.2 Importing FITS spectra into class 1 set angle sec 2 fits read single 3 sic delete single.30m 4 file out single.30m new 5 write 1 6 file in single.30m 7 find 8 get f 9 plot 1. Angles are expressed in arcseconds. 2. Read a single FITS spectrum.
2.7. READING/WRITING FITS FILE 11 3-4 Open a new .30m file. 3. Write the FITS spectrum in the .30m file with index number 1. 6-9 Check the result by plotting the spectrum from the .30m file.
Page 1: class Continuum and Line Analysis S
Page 4 and 5: iv CONTENTS 3.4 Communication with
Page 6 and 7: vi CONTENTS 5.2.21 STAMP . . . . .
Page 8 and 9: 2 CHAPTER 1. INTRODUCTION
Page 10 and 11: 4 CHAPTER 2. COOKBOOK 30 swap 31 wr
Page 12 and 13: 6 CHAPTER 2. COOKBOOK A4: the multi
Page 14 and 15: 8 CHAPTER 2. COOKBOOK Figure 2.1: R
Page 18 and 19: 12 CHAPTER 2. COOKBOOK
Page 20 and 21: 14 CHAPTER 3. USER MANUEL 3.1.3 Sca
Page 22 and 23: 16 CHAPTER 3. USER MANUEL 3.1.7 Var
Page 24 and 25: 18 CHAPTER 3. USER MANUEL • SET M
Page 26 and 27: 20 CHAPTER 3. USER MANUEL When work
Page 28 and 29: 22 CHAPTER 3. USER MANUEL • METHO
Page 30 and 31: 24 CHAPTER 3. USER MANUEL when only
Page 32 and 33: 26 CHAPTER 3. USER MANUEL • LINES
Page 34 and 35: 28 CHAPTER 3. USER MANUEL • SET T
Page 36 and 37: 30 CHAPTER 3. USER MANUEL 2. OR The
Page 38 and 39: 32 CHAPTER 4. DEVELOPER MANUAL (04-
Page 60 and 61: 54 CHAPTER 5. INTERNAL HELPS SPECTR
Page 62 and 63: 56 CHAPTER 5. INTERNAL HELPS ALIGN
Page 64 and 65: 58 CHAPTER 5. INTERNAL HELPS Plot a
Page 66 and 67:
60 CHAPTER 5. INTERNAL HELPS lower
Page 68 and 69:
62 CHAPTER 5. INTERNAL HELPS TOR\FI
Page 70 and 71:
64 CHAPTER 5. INTERNAL HELPS N Numb
Page 72 and 73:
66 CHAPTER 5. INTERNAL HELPS MODIFY
Page 74 and 75:
68 CHAPTER 5. INTERNAL HELPS If the
Page 76 and 77:
70 CHAPTER 5. INTERNAL HELPS PLOT /
Page 78 and 79:
72 CHAPTER 5. INTERNAL HELPS SET CA
Page 80 and 81:
74 CHAPTER 5. INTERNAL HELPS - SET
Page 82 and 83:
76 CHAPTER 5. INTERNAL HELPS ii) li
Page 84 and 85:
78 CHAPTER 5. INTERNAL HELPS SET SE
Page 86 and 87:
80 CHAPTER 5. INTERNAL HELPS Specif
Page 88 and 89:
82 CHAPTER 5. INTERNAL HELPS PARAME
Page 90 and 91:
84 CHAPTER 5. INTERNAL HELPS DRIFT
Page 92 and 93:
86 CHAPTER 5. INTERNAL HELPS SET WI
Page 94 and 95:
88 CHAPTER 5. INTERNAL HELPS Writes
Page 96 and 97:
90 CHAPTER 5. INTERNAL HELPS double
Page 98 and 99:
92 CHAPTER 5. INTERNAL HELPS units,
Page 100 and 101:
94 CHAPTER 5. INTERNAL HELPS 5.2.9
Page 102 and 103:
96 CHAPTER 5. INTERNAL HELPS MAP /N
Page 104 and 105:
98 CHAPTER 5. INTERNAL HELPS POP wi
Page 106 and 107:
100 CHAPTER 5. INTERNAL HELPS Xval
Page 108 and 109:
102 CHAPTER 5. INTERNAL HELPS speci
Page 110 and 111:
104 CHAPTER 5. INTERNAL HELPS siste
Page 112 and 113:
106 CHAPTER 5. INTERNAL HELPS GAUSS
Page 114 and 115:
108 CHAPTER 5. INTERNAL HELPS CONTI
Page 116 and 117:
110 CHAPTER 5. INTERNAL HELPS MAP%R
Page 118 and 119:
112 CHAPTER 5. INTERNAL HELPS 5.6.3
Page 120 and 121:
114CHAPTER 6. ERROR MESSAGES AND RE
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
138 INDEX MODIFY, 65 BANDS, 66 BEAM
show all

class Continuum and Line Analysis Single-dish Software - IRAM

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?