Jandy CL series cartridge filter - Inyo Swimming Pool Products

More documents

Recommendations

Info

Page 6Section 3. Installation Instructions3.1 Filter Location1. Select a well-drained area, one that does not floodwhen it rains. Damp, non-ventilated areas shouldbe avoided.2. Provide solid mounting for the filter and pumpsystem. Install system on a concrete slab or solidconcrete blocks to avoid risk of settlement. Do notuse sand to level the filter as the sand will washaway. Filter systems can weigh up to 800 lbs.3. Install electrical controls at least five (5) feet fromthe filter. This will allow enough room to standaway from the filter during start-up.4. Allow sufficient clearance around the filter topermit a visual inspection of the clamp ring (seeFig. 2).5. Allow sufficient space above the filter to removethe filter lid and filter element for cleaning andservicing.6. Position the filter to safely direct water drainage.Align the air release valve to safely direct purgedair or water.WARNINGWater discharged from an improperly positioned fi lteror valve can create an electrical hazard which cancause death, serious injury or property damage.CAUTIONMaintain your pressure gauge in good work ing order.The pressure gauge is the primary indicator of howthe fi lter is operating.7. If the filter needs to be located above the waterlevel of the pool, it can be raised 2.5 ft. withoutaffecting the pump efficiency. A check valve isrecommended on the suction line to the pump.8. If the filter is to be installed below the water levelof the pool, isolation valves should be installed onboth the suction and return lines to prevent backflow of pool water during any routine servicingthat may be required.3.2 Filter Preparation1. Check carton for damage due to rough handlingin shipment. If carton or any filter components aredamaged, notify carrier immediately.2. Carefully remove the accessory package.3. A visual inspection of all parts should be madenow. See parts list on page 12.4. With the carton in an upright position, remove thefilter tank from the carton.5. To mount the pressure gauge/air release assemblyto the top of the filter tank (located in the accessorybag):a. Place the smaller, thicker o-ring onto thethreads of the tank adapter (see Fig. 3). Slidethe tank adapter through the coupling nut andinto the filter tank. Use the flats on the tankadapter to tighten. Do not overtighten.b. Place the larger, thinner o-ring onto the gaugehousing. Thread the housing into the coupleron the tank adapter.c. Orient the gauge/air release assembly in thedesired position. Raise and thread the locknutonto the bottom of the gauge/air releaseassembly. Hand tighten the nut only. Usinga wrench to tighten the nut may damage thenut, gauge or air release assembly.6" MINIMUM CLEARANCEFILTER6" MINIMUMCLEARANCEHousingO-RingTank AdapterTank Adapter to HousingCouplerO-RingFigure 2.Filter LocationFigure 3.Pressure Gauge/Air Release Assembly
Cartridge Pool Filters - CL Series FilterPage 7Laars HeaterOutlet PortSpa Make UpInlet PortWaterfallJandyCheckValveJandy FilterFrom PoolDrainJandy PumpSpa ReturnPool ReturnSpa SuctionFrom Pool SkimmerFigure 4.Basic Pool/Spa Combination Plumbing3.3 Filter Installation1. This filter operates under pressure. When clampedproperly and operated without air in the watersystem, this filter will operate in a safe manner.2. If doubt exists as to the pressure which the systemwill be subjected to, install an ASME approvedautomatic Pressure Relief Valve or PressureRegulator in the circulation system set to thelowest working pressure of any of the componentsin the system.3. Place the filter on the concrete pad, lined up withthe inlet/outlet pipes (see Fig. 4).line leaks may cause air to be entrapped in filtertank or loss of prime at the pump. Pump dischargeline leaks may show up as dampness or jets ofwater.8. Support the inlet/outlet pipes independently toprevent any undue strains on the filter valve.9. Connect the pipes using the unions supplied withthe filter. Do not use teflon tape or pipe dope onany unions. Assemble the unions dry and handtighten.4. To reduce pressure losses, 2" (minimum) piping isrecommended for plumbing the system.5. For best efficiency use the fewest possible numberof fittings. This will prevent a restriction in thewater flow.6. Make all plumbing connections in accordancewith local plumbing and building codes. Filterconnections are provided with an o-ring seal. Toavoid damage to the o-rings, use only a siliconebase lubricant on the o-rings. Do not use pipe jointcompound, glue or solvent on inlet/outlet unioncoupling nuts.7. Keep piping tight and free of leaks. Pump suction
Page 1: H0238700DInstallation and Operation
Page 4 and 5: Page 4Section 1. Safety Information
Page 8 and 9: Page 8WARNINGFollow these instructi
Page 10 and 11: Page 1010. Using new cartridges or
Page 12 and 13: Page 12Section 9. Parts List and Ex
Page 14 and 15: Page 14NOTES
Page 16: H0238700DLIMITED WARRANTYThank you

Jandy CL series cartridge filter - Inyo Swimming Pool Products

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?