EFIS-D60 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Wiring OverviewWIRING SYSTEM OVERVIEWThe following block diagram depicts the basic layout of the EFIS DB25 electrical connectionsand is for reference only. Read the specific instructions for each connection prior to installation.The colors shown refer to the Dynon-supplied EFIS harness2-4 EFIS-D60 Installation Guide
3. INSTRUMENT INSTALLATIONThis section provides you with the information needed to physically and electrically install theEFIS-D60.Selecting a Remote Compass Module LocationFinding a good location for the EDC-D10Aremote compass module is critical to anaccurate EFIS-D60 heading display. Keep inmind that calibration can compensate forsmall static magnetic fields superimposedupon the earth’s field; it cannot takeinto account dynamic effects likeAC currents, non-constant DCcurrents and non-stationary ferrousmaterial (e.g., an electric turncoordinator). Use the followingsuggestions to help you find a goodlocation for your EDC-D10A.• Keep the EDC-D10A away fromany source of magnetic fields(such as electrical equipment and currentcarryingwires) and ferrous material.• Move a handheld compass throughout thespace surrounding your location to get a roughidea of the suitability of your chosen location.If the needle deviates significantly frommagnetic north in any given area, that locationwould not be ideal for the EDC-D10A.• The EDC-D10A can be mounted anywhere inthe aircraft (away from magnetic interference)such that its pitch is as close to that of theEFIS-D60 as possible. It does not need to bedirectly along any axis of the EFIS-D60. Itshould be mounted with the long axisparallel to the wings, the electricalconnector facing toward the front of theplane, and the mounting tabs on the bottom.The bracket used to hold the EDC-D10Amust hold the EDC-D10A at the same pitch,roll, and yaw as the EFIS-D60 with respectto the airframe. We recommend that you usean electronic level, if available, to makesure the EDC-D10A is aligned with theEFIS-D60 to better than 1 degree.Connector towarddirection of flightConnector forward andtabs mounted downSide view of EDC-D10A, tabs mounteddown and aligned within 1 degree of pitchwith EFIS-D60EFIS-D60 Installation Guide 3-1
Page 1: EFIS-D60Installation GuideThis prod
Page 5: Table of ContentsContact Informatio
Page 8 and 9: IntroductionAbout this GuideIn the
Page 10 and 11: Wiring Overview25-Pin Female EFIS H
Page 14 and 15: Instrument Installation• All moun
Page 16 and 17: Instrument InstallationPC CONNECTIO
Page 18 and 19: Instrument InstallationSERIAL ALTIT
Page 20 and 21: Instrument InstallationPanel Locati
Page 23 and 24: 4. EFIS CALIBRATION AND CONFIGURATI
Page 25 and 26: EFIS Calibration and ConfigurationE
Page 27 and 28: 5. APPENDIXThe appendices contain a
Page 29 and 30: Alert Message Description End condi
Page 31 and 32: AppendixProblemAfter performing a m
Page 33 and 34: AppendixAppendix B: Dynon AOA/Pitot
Page 35 and 36: Appendixinstructions on the followi
Page 37 and 38: Appendixcontroller. Remember that e
Page 39 and 40: AppendixBoom mountPLUMBINGNOTE: Bec
Page 41 and 42: AppendixAppendix C: Encoder Serial-
Page 43 and 44: AppendixEFISDB25Pin#13Dynon EFIShar
Page 45: AppendixAppendix F: WeightsAdding a

EFIS-D60 Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?