EFIS-D60 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Instrument InstallationSERIAL ALTITUDE FORMATSThere are four formats used by serial transponders. Choose the correct format for yourtransponder in the ALTENC menu, using the FRMAT button.Format 1Used By Dynon Encoder Serial-to-Gray Code Converter, GarminAT (formerly UPS Aviation Technologies)Baud rate 1200Format#AL, space, +/-sign, five altitude bytes, T+25, checksum,carriage returnExample message #AL +05200T+25D7[CR]Format 2Used By MagellanBaud rate 1200Format$MGL, +/- sign, five altitude digits, T+25, checksum, carriagereturnExample message $MGL+05200T+25E3[CR]Format 3Used By Northstar, GarminBaud rate 2400FormatALT, space, five altitude bytes, carriage returnExample message ALT 05200[CR]Format 4Used ByGarmin GTX327, GTX328, and GTX330 (set on Icarusinput), Icarus, TrimbleBaud rate 9600FormatALT, space, five altitude bytes, carriage returnExample message ALT 05200[CR]3-6 EFIS-D60 Installation Guide
Instrument InstallationAudio Alert OutputThe EFIS-D60 has an audio alert output for DB25 Color Functionsounding AOA and altitude alarms through pin#an intercom or audio panel. You must havethe optional AOA Pitot Probe to use thisfunctionality.18 Green EFIS Audio Alert OutputConnect the alarm output from the EFIS-D60 to the outside terminal of a 10 kΩ variable resistor(not included). Ensure that audio outputs are connected similar to the following diagram. The 10kΩ variable resistor can be obtained from Radio Shack (P/N 271-1715) or other electronicssuppliers.Outside terminal To EFIS-D60 AudioAlert OutCenter terminalOutside terminalTo intercom/audiopanel auxiliary input.To groundTo set the volume of the AOA alarm, you will need your EFIS-D60 powered on and the alarmoutput wired as described above. Enter the EFIS menu by pressing any button (except theleftmost or rightmost) beneath an EFIS page. Press SETUP > AOAALM. In that menu, press theTEST button. While the button is held down, the AOA alarm will sound. Adjust the variableresistor until the volume in the intercom or audio panel is at an acceptable level.EFIS-D60 Installation Guide 3-7
Page 1: EFIS-D60Installation GuideThis prod
Page 5: Table of ContentsContact Informatio
Page 8 and 9: IntroductionAbout this GuideIn the
Page 10 and 11: Wiring Overview25-Pin Female EFIS H
Page 12 and 13: Wiring OverviewWIRING SYSTEM OVERVI
Page 14 and 15: Instrument Installation• All moun
Page 16 and 17: Instrument InstallationPC CONNECTIO
Page 20 and 21: Instrument InstallationPanel Locati
Page 23 and 24: 4. EFIS CALIBRATION AND CONFIGURATI
Page 25 and 26: EFIS Calibration and ConfigurationE
Page 27 and 28: 5. APPENDIXThe appendices contain a
Page 29 and 30: Alert Message Description End condi
Page 31 and 32: AppendixProblemAfter performing a m
Page 33 and 34: AppendixAppendix B: Dynon AOA/Pitot
Page 35 and 36: Appendixinstructions on the followi
Page 37 and 38: Appendixcontroller. Remember that e
Page 39 and 40: AppendixBoom mountPLUMBINGNOTE: Bec
Page 41 and 42: AppendixAppendix C: Encoder Serial-
Page 43 and 44: AppendixEFISDB25Pin#13Dynon EFIShar
Page 45: AppendixAppendix F: WeightsAdding a

EFIS-D60 Installation Guide - Dynon Avionics

Create successful ePaper yourself

Delete template?

Save as template?