EFIS-D60 Installation Guide - Dynon Avionics

More documents

Recommendations

Info

Appendixdirectly to your switched avionics power. Ensure that all avionics power is off before performingthe wiring step of this installation.If your Altitude Transponder has either a strobe signal or a D4 pin, leave these pins unconnected.Transponder PinA1A2A4B1B2B4C1C2C4Power (10V-30V)GndStrobe SignalEncoder ConverterWire ColorYellowGreenWhite with BlueBlueOrangeWhite with RedWhite with GreenWhiteWhite with BlackRedBlackNo ConnectionThe Gray code output of the Encoder Converter reports altitude not adjusted for barometricpressure, as required by FAA specification. The altitude reported by the EFIS-D60 encoder willalways match the altitude shown on screen when the BARO value is set to 29.92 inHg.STEP 2: CONNECTING TO THE EFIS-D60Before wiring connections to the EFIS-D60 check to ensure that the wire length between yourEncoder Converter and your EFIS-D60 is appropriate. Add or remove wire length if needed ordesired. Customizing the wire length will facilitate an installation that is both cleaner and moresecure.The only pins of interest on the EFIS-D60 connector for the Encoder Converter installation arepins 13 and 21. The two wires exiting the Encoder Converter are the EFIS-TX and the EFIS-Ground, which are green (or red) and black respectively, and 2 feet in length. Connect thesewires to the EFIS-D60 25-pin female harness.Ensure that your EFIS-D60 is powered off. Then connect the black EFIS Ground wire to pin 21.Then, connect the green wire to pin 13 (Serial Encoder Transmit) on the EFIS harness.5-16 EFIS-D60 Installation Guide
AppendixEFISDB25Pin#13Dynon EFISharness colorBlue/White (may beblack on someharnesses)Encoder ConverterWire ColorGreen (May be Red onolder models)FunctionSerial EncoderTransmit21 White Black Serial Encoder GroundSTEP 3: EFIS-D60 ENCODER FORMATFor proper communication the EFIS Altitude Encoder format must be set to format number one.To change this setting, from the main menu, select: SETUP > ALTENC. Press FRMAT until itreads “1.”EFIS-D60 Installation Guide 5-17
Page 1: EFIS-D60Installation GuideThis prod
Page 5: Table of ContentsContact Informatio
Page 8 and 9: IntroductionAbout this GuideIn the
Page 10 and 11: Wiring Overview25-Pin Female EFIS H
Page 12 and 13: Wiring OverviewWIRING SYSTEM OVERVI
Page 14 and 15: Instrument Installation• All moun
Page 16 and 17: Instrument InstallationPC CONNECTIO
Page 18 and 19: Instrument InstallationSERIAL ALTIT
Page 20 and 21: Instrument InstallationPanel Locati
Page 23 and 24: 4. EFIS CALIBRATION AND CONFIGURATI
Page 25 and 26: EFIS Calibration and ConfigurationE
Page 27 and 28: 5. APPENDIXThe appendices contain a
Page 29 and 30: Alert Message Description End condi
Page 31 and 32: AppendixProblemAfter performing a m
Page 33 and 34: AppendixAppendix B: Dynon AOA/Pitot
Page 35 and 36: Appendixinstructions on the followi
Page 37 and 38: Appendixcontroller. Remember that e
Page 39 and 40: AppendixBoom mountPLUMBINGNOTE: Bec
Page 41: AppendixAppendix C: Encoder Serial-
Page 45: AppendixAppendix F: WeightsAdding a

EFIS-D60 Installation Guide - Dynon Avionics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?