owneRs manual: Handling & SafeTy inSTrucTionS - Sig Sauer

More documents

Recommendations

Info

<strong>Sig</strong>ht DeploymentFlip up the front sight assembly until it held in the upright position by the detent.Flip up the rear sight assembly until it is held in the upright position by the detent.When the sights are not longer required, rotate them down to their stowed position.Windage Adjustment (Left/Right)Windage ScrewFIG 18 REAR SIGHT WINDAGE ADJUSTMENTElevation AdjustmentWindage ScrewFIG 19 FRONT SIGHT POST DETAILING DETENT FOR ADJUSTMENT36 www.sigsauer.com
when it counts CHANGES IN POINT OF IMPACT ON A 25M TARGET (16.0” BARREL)ELEVATIONWINDAGE1 CLICK 1.2cm 1 CLICK 0.5cm2 CLICKS 2.3cm 2 CLICKS 0.9cm3 CLICKS 3.5cm 3 CLICKS 1.4cm4 CLICKS 4.7cm 4 CLICKS 1.9cmTo move your shot group UP rotate the front sight post clockwiseTo move your shot group DOWN rotate the front sight post counter clockwiseTo move your shot group to the LEFT rotate the windage screw counter clockwiseTo move your shot group to the RIGHT rotate the windage screw clockwisewww.sigsauer.com 37
Page 1: when it counts ®OWNERS MANUAL: Han
Page 6 and 7: WARNING - LOCKING DEVICESThis firea
Page 8 and 9: TopicTABLE OF CONTENTSPageState by
Page 10 and 11: TopicPage6.0 Procedures in case of
Page 12 and 13: WARNINGS OF GREAT IMPORTANCEARE FOU
Page 14 and 15: GENERAL SAFETY INFORMATION AND MECH
Page 16 and 17: 1.1 Protect Your Eyes And EarsAlway
Page 19 and 20: when it counts 8. Do not oil cartri
Page 21 and 22: when it counts 2.0. Mechanical Char
Page 23 and 24: when it counts 2.1.4. Quad Rail Han
Page 25 and 26: when it counts MANUAL SAFETY “ON
Page 27 and 28: when it counts 2.1.6.A. Position #1
Page 29 and 30: when it counts When the cycle of op
Page 31 and 32: when it counts To remove the butt s
Page 33 and 34: when it counts 2.1.8. Trigger Guard
Page 35: when it counts 2.1.9. SightsThe SIG
Page 39 and 40: when it counts 2.2. Technical Speci
Page 41 and 42: when it counts SEMI - The trigger i
Page 43: when it counts 3.2 Loading the Maga
Page 46 and 47: 3.5 Reloading the Rifle after firin
Page 48 and 49: 4.1. FiringRotate the fire control
Page 50 and 51: WARNING:Removing cartridges from th
Page 52 and 53: 6.2. Failure to Fire (Hot Rifle) Tr
Page 54 and 55: 6.4. Feedway Stoppage (Jam)A feedwa
Page 56 and 57: 1. Press the Pivot Pin (front pin)
Page 58 and 59: 7.3. Gas Valve and Pushrod Removal1
Page 60 and 61: 1. Remove the two (2) quad clamp sc
Page 62 and 63: 5. Remove the upper rail section.FI
Page 64 and 65: 8.0. Cleaning1. Your rifle is deliv
Page 66 and 67: 8.3. Cleaning the BoltA cotton patc
Page 68 and 69: 9.0 Reassembly9.1. Recoil Buffer an
Page 70 and 71: 9.2. Extractor1. Fit extractor to b
Page 72 and 73: 1. Re-insert the bolt into the bolt
Page 74 and 75: 9.4. Bolt Carrier Assembly to Upper
Page 76 and 77: 2. Place the upper rail section ove
Page 78 and 79: 9.7. Pushrod and Gas Valve re-assem
Page 80 and 81: 10.0. Perform a Function Check of t
Page 82 and 83: Bolt and Carrier Assembly• Extrac
Page 84 and 85: 13.0. Service and Replacement Parts
Page 86 and 87:
Service PolicyIf you have questions
Page 88 and 89:
ORDER PARTSIn the event you want to
Page 90 and 91:
16.0 Parts Diagram*90 www.sigsauer.
Page 92 and 93:
SIG SAUER ® Limited Lifetime Firea
Page 94 and 95:
Notes:94 www.sigsauer.com
show all

owneRs manual: Handling & SafeTy inSTrucTionS - Sig Sauer

Create successful ePaper yourself

Delete template?

Save as template?