owneRs manual: Handling & SafeTy inSTrucTionS - Sig Sauer

More documents

Recommendations

Info

WARNING:Removing cartridges from the magazine does not prevent the rifle from being fired! When there is a cartridge in thechamber and the safety lever is in the “F” (FIRE) position, the cartridge will discharge if the trigger is pulled. It is absolutelyessential for the user to know how to completely unload the rifle.“Completely” means emptying the magazine and removing a chambered cartridge. The safety lever should always be inthe “S” (SAFE) position when the rifle is being unloaded.THE RIFLE WILL FIRE EVEN IF THE MAGAZINE IS EMPTY OR REMOVED50 www.sigsauer.com
when it counts TO CLEAR A STOPPAGE (JAM)6.0. Procedures In Case of a StoppageA “Stoppage” is an interruption in the cycle of operation as depicted in Section 4.0. A stoppage can normally be repairedby the operator by performing one of the following immediate actions described.6.1. Failure to Fire (Cold Rifle) Trigger is pressed, hammer falls, rifle does not fire.1. Ensure the magazine is properly seated in the magazine well by applying upward pressure and then pulling down onthe magazine.2. Retract the charging handle all the way back and observe the ejection of the expended case or a live cartridge; and3. Visually inspect the chamber for any obstructions, if the chamber shows to be clear, release the charging handle tofeed a new cartridge. Do NOT ride the charging handle forward.4. Attempt to fire the rifle again.www.sigsauer.com 51
Page 1: when it counts ®OWNERS MANUAL: Han
Page 6 and 7: WARNING - LOCKING DEVICESThis firea
Page 8 and 9: TopicTABLE OF CONTENTSPageState by
Page 10 and 11: TopicPage6.0 Procedures in case of
Page 12 and 13: WARNINGS OF GREAT IMPORTANCEARE FOU
Page 14 and 15: GENERAL SAFETY INFORMATION AND MECH
Page 16 and 17: 1.1 Protect Your Eyes And EarsAlway
Page 19 and 20: when it counts 8. Do not oil cartri
Page 21 and 22: when it counts 2.0. Mechanical Char
Page 23 and 24: when it counts 2.1.4. Quad Rail Han
Page 25 and 26: when it counts MANUAL SAFETY “ON
Page 27 and 28: when it counts 2.1.6.A. Position #1
Page 29 and 30: when it counts When the cycle of op
Page 31 and 32: when it counts To remove the butt s
Page 33 and 34: when it counts 2.1.8. Trigger Guard
Page 35 and 36: when it counts 2.1.9. SightsThe SIG
Page 37 and 38: when it counts CHANGES IN POINT OF
Page 39 and 40: when it counts 2.2. Technical Speci
Page 41 and 42: when it counts SEMI - The trigger i
Page 43: when it counts 3.2 Loading the Maga
Page 46 and 47: 3.5 Reloading the Rifle after firin
Page 48 and 49: 4.1. FiringRotate the fire control
Page 52 and 53: 6.2. Failure to Fire (Hot Rifle) Tr
Page 54 and 55: 6.4. Feedway Stoppage (Jam)A feedwa
Page 56 and 57: 1. Press the Pivot Pin (front pin)
Page 58 and 59: 7.3. Gas Valve and Pushrod Removal1
Page 60 and 61: 1. Remove the two (2) quad clamp sc
Page 62 and 63: 5. Remove the upper rail section.FI
Page 64 and 65: 8.0. Cleaning1. Your rifle is deliv
Page 66 and 67: 8.3. Cleaning the BoltA cotton patc
Page 68 and 69: 9.0 Reassembly9.1. Recoil Buffer an
Page 70 and 71: 9.2. Extractor1. Fit extractor to b
Page 72 and 73: 1. Re-insert the bolt into the bolt
Page 74 and 75: 9.4. Bolt Carrier Assembly to Upper
Page 76 and 77: 2. Place the upper rail section ove
Page 78 and 79: 9.7. Pushrod and Gas Valve re-assem
Page 80 and 81: 10.0. Perform a Function Check of t
Page 82 and 83: Bolt and Carrier Assembly• Extrac
Page 84 and 85: 13.0. Service and Replacement Parts
Page 86 and 87: Service PolicyIf you have questions
Page 88 and 89: ORDER PARTSIn the event you want to
Page 90 and 91: 16.0 Parts Diagram*90 www.sigsauer.
Page 92 and 93: SIG SAUER ® Limited Lifetime Firea
Page 94 and 95: Notes:94 www.sigsauer.com

owneRs manual: Handling & SafeTy inSTrucTionS - Sig Sauer

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?