05-6193A01-A - GE Digital Energy

More documents

Recommendations

Info

The Event Log Menu (Figure 13) is used to display all events stored bythe transceiver, even if the radio has been power-cycled. It also shows arunning total of alarms stored. Select Show Log to view stored events, andClear Log to erase all stored entries.Figure 13. Event Log MenuThe I/O Statistics submenu (Figure 14) allows viewing transmitted andreceived bytes on any of the transceiver interface modules as selected bythe user. Available selections are: COM1, COM2, Ethernet data port, RemoteReprogram, Ethernet Interface, Modem, Drivers, Miscellaneous, All, Data Link Layer,Media Access Controller, and Port(s).Once a module is selected, a summary of TX and RX bytes is presented,along with the number of packets missed, retries, and number of blocks(as applicable, depending on the interface selection). The display is continuallyrefreshed to show the latest information, and may be cleared atany time by selecting Clear Module Statistics.Invisible place holderFigure 14. I/O Statistics Menu(Example shows Statistics for COM1 Interface)16 SD Series Serial-Telnet Supplement MDS 05-6193A01, Rev. A
The Ethernet Statistics Submenu (Figure 15) presents a detailed summaryof packets received and transmitted, dropped packets, errors, overrunsof the buffer, RX data rate (bps), and RX/TX data for Unicast, Multicast,and Broadcast transmissions. Data may be cleared at any time byselecting CLEAR from the menu.Invisible place holderFigure 15. Ethernet Statistics Submenu3.7 View/Set Radio (RF) Operating ParametersRF Output Power SettingThe RF output power of the transceiver may be set between 20 and 37dBm (0.1 to 5 watts) in1 dB increments. The default setting is 37 dBm.Full power is not required in many cases, and lower settings will placeless demand on the DC power supply and may reduce the chance ofinterference with other stations. Only the power necessary to carry outreliable communications should be usedTo view or adjust the RF output power setting, proceed as follows:1. Access the Basic Settings Menu by following this navigation path:Radio Configuration Menu>>Basic Settings Menu (see Figure 16). The powerlevel is displayed to the right of RF Output Power.2. If changes are needed, select RF Output Power and enter a new value inthe field to the right of the parameter. Press the ENTER key to applythe change.MDS 05-6193A01, Rev. A SD Series Serial-Telnet Supplement 17
Page 1 and 2: MDS SD SeriesSerial/Telnet Manageme
Page 3 and 4: TABLE OF CONTENTS1.0 INTRODUCTION .
Page 5 and 6: Copyright and TrademarkThis manual
Page 7 and 8: 1.0 INTRODUCTIONThis document is a
Page 9 and 10: NOTE:TX and RX frequencies may not
Page 11 and 12: 3.0 USING THE MENU SYSTEMThis secti
Page 13 and 14: Invisible place holderMENU SYSTEMOv
Page 15 and 16: Table 1. Menu Selection Chart (Cont
Page 17 and 18: Table 1. Menu Selection Chart (Cont
Page 19 and 20: Figure 7. Starting Information Scre
Page 21: Invisible place holderFigure 11. St
Page 25 and 26: 1) For MDS x710-compatible operatio
Page 27 and 28: TX Time-OutTX Time-Out protects aga
Page 29 and 30: 1. Select Switched Carrier from the
Page 31 and 32: A related setting to Timeout is Pac
Page 33 and 34: To view detailed version informatio
Page 35 and 36: 1. To select the LED Mode, access t
Page 37 and 38: Invisible place holderFigure 24. Mu
Page 39 and 40: Invisible place holderFigure 26. Me
Page 41 and 42: DLINK StatusThis item is used to en
Page 43 and 44: Setting the AES Wireless Security P
Page 45 and 46: Telnet AccessTelnet access is a pow
Page 47 and 48: 2. Enter an IPv4-compliant IP addre
Page 49 and 50: Basic Bridge FilterSelectionThe pur
Page 51 and 52: IP Payload is intended to be used i
Page 53 and 54: Setting the ModeThe operating mode
Page 55 and 56: The Terminal Server supports the fo
Page 57 and 58: TCP Server IP PortThis selection sp
Page 59 and 60: 1. Select Data ID on the menu. A fl
Page 61 and 62: DHCPDynamic Host Configuration Prot
Page 63 and 64: 2. Press the spacebar until the des
Page 65 and 66: 1. Select Data Format from the menu
Page 67 and 68: To save the radio’s current confi
Page 69 and 70: Invisible place holderFigure 47. Re
Page 71 and 72: 4. To dekey the radio, select Key R
Page 73 and 74:
Invisible place holderReprogramming
Page 75 and 76:
Invisible place holderRemote Reprog
Page 77 and 78:
Viewing Enabled FeaturesThe radio
Page 79 and 80:
Alarm Signal Mask(Hex)This selectio
Page 81 and 82:
Checking for AlarmsTo check for ala
Page 83 and 84:
Invisible place holderFigure 62. I/
Page 85 and 86:
1. Program one radio in the network
Page 87 and 88:
NOTE: It is possible for Remote rad
Page 89 and 90:
Invisible place holderFigure 65. Ma
Page 91 and 92:
From Menu Mode to...From Diagnostic
Page 93 and 94:
LOCAL PC WITH FIRMWARE FILEInvisibl
Page 95 and 96:
6. Access the Local Reprogram scree
Page 97 and 98:
APPENDIX-ACLI SCRIPTING INTERFACENO
Page 99 and 100:
Detailed Command DescriptionsALARMS
Page 101 and 102:
8N2—eight char bits, no parity, t
Page 103 and 104:
OFF—Sleep Mode offON—Sleep Mode
Page 105 and 106:
CLEAR—Clear selected statisticsMO
Page 107 and 108:
LOGOUTMENUMULTIHOSTLogs the user ou
Page 109 and 110:
MPT1411—Analog9600B—x710B compa
Page 111 and 112:
1—Minimum delay255—Maximum dela
Page 113 and 114:
IN CASE OF DIFFICULTY...GE MDS prod
show all

05-6193A01-A - GE Digital Energy

Create successful ePaper yourself

Delete template?

Save as template?