05-6193A01-A - GE Digital Energy

More documents

Recommendations

Info

Invisible place holderConfiguring the IP SettingsFigure 32. Ethernet Configuration MenuThe IP Configuration Menu (Figure 33) contains various settings for theIP data stream. Each item is listed below along with instructions formaking changes. Note that the bottom of the screen displays the currentsettings that have been applied to the radio in a read-only fashion.Invisible place holderFigure 33. IP Configuration MenuStatic IP AddressThe radio requires a local IP address to support remote management andserial device (terminal server) services. An IPv4 IP address should beentered in this field, unless DHCP is enabled, in which case it is notrequired. To set or change the radio’s static IP address, proceed as follows:1. Select Static IP Address from the menu. The field to the right clears anda flashing cursor appears.40 SD Series Serial-Telnet Supplement MDS 05-6193A01, Rev. A
2. Enter an IPv4-compliant IP address string and press ENTER to applythe change.Static IP NetmaskThis refers to the radio’s IPv4 local subnet mask. This parameter is usedwhen the radio attempts to send a locally-initiated message, either fromthe terminal server, or a management process. You need not define it ifDHCP is enabled. To set or change the radio’s static IP netmask, proceedas follows:1. Select Static IP Netmask from the menu. The field to the right clearsand a flashing cursor appears.2. Enter an IPv4-compliant IP netmask string and press ENTER to applythe change.Static Default GatewayThis is the IPv4 address of the default gateway device, typically a routerconnected to the radio. To set or change the static default gateway, proceedas follows:1. Select Static Default Gateway from the menu. The field to the right clearsand a flashing cursor appears.2. Enter an IPv4-compliant static gateway address and press ENTER toapply the change.DHCPDynamic Host Configuration Protocol (DHCP) handles the assignmentof IP parameters (Address, Netmask, Gateway) to all units in a network,and allows for introducing new devices on the network with minimalmanual intervention. The assigned parameters are valid for a specific“lease” time, at which point they can be reassigned or renewed. Toenable or disable DHCP, proceed as follows:1. Select DHCP from the menu. A flashing cursor appears in the field tothe right.2. Press the spacebar until the desired state (Enabled or Disabled) is displayedand press ENTER to apply the change.Ethernet Bridge ConfigurationEthernet Bridging is a feature that allows the radio to transparentlyexchange Ethernet packets with other properly configured units. In thisway, locally-connected devices at the Master site (e.g., a PC or PLC) cancommunicate via Ethernet with devices connected at Remote radios(e.g., an RTU or other data device), and vise versa.NOTE: To make use of Ethernet Bridging, the radio must be properlyauthorized. If it is not, contact your sales representative forfurther information. Bridging is only available on ES models.MDS 05-6193A01, Rev. A SD Series Serial-Telnet Supplement 41
Page 1 and 2: MDS SD SeriesSerial/Telnet Manageme
Page 3 and 4: TABLE OF CONTENTS1.0 INTRODUCTION .
Page 5 and 6: Copyright and TrademarkThis manual
Page 7 and 8: 1.0 INTRODUCTIONThis document is a
Page 9 and 10: NOTE:TX and RX frequencies may not
Page 11 and 12: 3.0 USING THE MENU SYSTEMThis secti
Page 13 and 14: Invisible place holderMENU SYSTEMOv
Page 15 and 16: Table 1. Menu Selection Chart (Cont
Page 17 and 18: Table 1. Menu Selection Chart (Cont
Page 19 and 20: Figure 7. Starting Information Scre
Page 21 and 22: Invisible place holderFigure 11. St
Page 23 and 24: The Ethernet Statistics Submenu (Fi
Page 25 and 26: 1) For MDS x710-compatible operatio
Page 27 and 28: TX Time-OutTX Time-Out protects aga
Page 29 and 30: 1. Select Switched Carrier from the
Page 31 and 32: A related setting to Timeout is Pac
Page 33 and 34: To view detailed version informatio
Page 35 and 36: 1. To select the LED Mode, access t
Page 37 and 38: Invisible place holderFigure 24. Mu
Page 39 and 40: Invisible place holderFigure 26. Me
Page 41 and 42: DLINK StatusThis item is used to en
Page 43 and 44: Setting the AES Wireless Security P
Page 45: Telnet AccessTelnet access is a pow
Page 49 and 50: Basic Bridge FilterSelectionThe pur
Page 51 and 52: IP Payload is intended to be used i
Page 53 and 54: Setting the ModeThe operating mode
Page 55 and 56: The Terminal Server supports the fo
Page 57 and 58: TCP Server IP PortThis selection sp
Page 59 and 60: 1. Select Data ID on the menu. A fl
Page 61 and 62: DHCPDynamic Host Configuration Prot
Page 63 and 64: 2. Press the spacebar until the des
Page 65 and 66: 1. Select Data Format from the menu
Page 67 and 68: To save the radio’s current confi
Page 69 and 70: Invisible place holderFigure 47. Re
Page 71 and 72: 4. To dekey the radio, select Key R
Page 73 and 74: Invisible place holderReprogramming
Page 75 and 76: Invisible place holderRemote Reprog
Page 77 and 78: Viewing Enabled FeaturesThe radio
Page 79 and 80: Alarm Signal Mask(Hex)This selectio
Page 81 and 82: Checking for AlarmsTo check for ala
Page 83 and 84: Invisible place holderFigure 62. I/
Page 85 and 86: 1. Program one radio in the network
Page 87 and 88: NOTE: It is possible for Remote rad
Page 89 and 90: Invisible place holderFigure 65. Ma
Page 91 and 92: From Menu Mode to...From Diagnostic
Page 93 and 94: LOCAL PC WITH FIRMWARE FILEInvisibl
Page 95 and 96: 6. Access the Local Reprogram scree
Page 97 and 98:
APPENDIX-ACLI SCRIPTING INTERFACENO
Page 99 and 100:
Detailed Command DescriptionsALARMS
Page 101 and 102:
8N2—eight char bits, no parity, t
Page 103 and 104:
OFF—Sleep Mode offON—Sleep Mode
Page 105 and 106:
CLEAR—Clear selected statisticsMO
Page 107 and 108:
LOGOUTMENUMULTIHOSTLogs the user ou
Page 109 and 110:
MPT1411—Analog9600B—x710B compa
Page 111 and 112:
1—Minimum delay255—Maximum dela
Page 113 and 114:
IN CASE OF DIFFICULTY...GE MDS prod
show all

05-6193A01-A - GE Digital Energy

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?