Triton Topaz T100si - Faucets, Showers, Bathroom, Kitchen, More.

More documents

Recommendations

Info

Topaz T100siCONTENTSPageImportant safety information 1Introduction 2Specifications 2Understanding your Topaz 2Key to main components 3Electrical requirements 4 − 5Water requirements 6Siting of the shower 7 − 8Fitting the shower to the wall 9Plumbing connections 10Electrical connections 11Commissioning 12 − 13Replacing the cover 13Operating the shower 14 − 16Operating functions 17 − 18Changing the fascia 18Fitting the antler riser rail 19 − 20Fitting the Antler hose and showerhead 20Fitting the arc riser rail 21 − 22Fitting the ARC hose and showerhead 22Adjusting the showerhead 23Cleaning the showerhead 24Cleaning the inlet filter 25Cleaning the scale trap 26Spare parts 27 − 28Fault finding 29 − 30Guarantee, service policy, etc.rear coverTo check the product suitability for commercial and multiple installations, please contactTriton’s specification advisory service before installation.Telephone: +44 (0) 24 7632 5491Facsimile: +44 (0) 24 7632 4564E mail: technical@triton.plc.uk
Topaz T100siPlease Read This Important Safety Information Products manufactured by Triton are safe and without risk provided they are installed,used and maintained in good working order in accordance with our instructions andrecommendations. WARNING: Do not operate shower if frozen, or suspected of being frozen. It mustthaw out before using. Do not operate the unit if the showerhead or spray hose becomes damaged. Do not restrict flow out of shower by placing showerhead in direct contact with your body. Do not operate the shower if water ceases to flow during use or if water has entered inside1 General1.1 Isolate the electrical and water supplies beforeremoving the cover.1.2 Read all of these instructions and retain themfor later use.1.3 Do not take risks with plumbing or electricalequipment.1.4 Isolate electrical and water supplies beforeproceeding with the installation.1.5 The unit must be mounted onto the finishedwall surface (on top of the tiles). Do not tileup to unit after fixing to wall.1.6 Contact Customer Service (see back page), ifany of the following occur:a) If it is intended to operate the shower atpressures above the maximum or below theminimum stated.b) If the unit shows a distinct change inperformance.c) If the shower is frozen.1.7 If it is intended to operate the shower in areasof hard water (above 200 ppm temporaryhardness), a scale inhibitor may have to befitted. For advice on the Triton Scale Inhibitor,contact Triton Customer Service.1.8 The showerhead must be cleaned regularlywith descalent to remove scale and debris,otherwise restrictions to the flow on the outletof the unit will result in higher temperaturesand could also cause the Pressure Relief Devicein the unit to operate.1.9 This product is not suitable for mounting intosteam rooms or steam cubicles.2 Plumbing2.1 The plumbing installation must comply withWater Regulations, Building Regulations orany particular regulations as specified by LocalWater Company or Water Undertakers andshould be in accordance with BS 6700.2.2 The supply pipe must be flushed to clear debrisbefore connecting to the shower unit.2.3 Do not solder pipes or fittings within 300mmof the shower appliance, as heat transfer candamage components.2.4 Do not fit any form of outlet flow control asthe outlet acts as a vent for the heater can.2.5 Do not use excessive force when makingconnections to the flexible hose orshowerhead, finger tight is sufficient.2.6 All plumbing connections must be completedbefore making the electrical connections.3 Electrical3.1 The installation must comply with BS 7671‘Requirements for electrical installations’ (IEEwiring regulations), building regulations or anyparticular regulations as specified by the localElectrical Supply Company.3.2 This appliance must be earthed.3.3 In accordance with ‘The Plugs and Sockets etc.(Safety) Regulations 1994’, this appliance isintended to be permanently connected to thefixed wiring of the electrical mains system.3.4 Make sure all electrical connections are tight toprevent overheating.3.5 Fuses do not give personal protection againstelectric shock.3.6 To enhance electrical safety a 30mA residualcurrent device (RCD) should be installed in allUK electric and pumped shower circuits. Thismay be part of the consumer unit or a separateunit.3.7 Switch off immediately at the isolating switch ifwater ceases to flow during use.3.8 Other electrical equipment i.e. extractor fans,pumps must not be connected to the circuitswithin the unit.3.9 Switch off at isolating switch when not in use.This is a safety procedure recommended withall electrical appliances.3.10 As with all electrical appliances it isrecommended to have the shower andinstallation checked at least every two years bya competent electrician to make sure there isno deterioration due to age and usage.
Page 1: Topaz T100sithermostaticcontrol ele
Page 5 and 6: Topaz T100siFig.1KEY TO MAIN COMPON
Page 7: Topaz T100siparts of other applianc
Page 10 and 11: Topaz T100siFig.7which can cause th
Page 12 and 13: Topaz T100siFig.12warning!Inletfilt
Page 14 and 15: Topaz T100siFig.14Fig.15Valvespindl
Page 16 and 17: Topaz T100siFig.17Power buttonCold
Page 18 and 19: Topaz T100siFig.26Fig.27Fig.28Fig.2
Page 20 and 21: Topaz T100siFig.32WARNING!After any
Page 22 and 23: Topaz T100siFig.37Fig.38Fig.39Showe
Page 24 and 25: Topaz T100siFig.45similar through t
Page 26 and 27: Topaz T100siFig.51SprayplatekeyCLEA
Page 28 and 29: Topaz T100siinstructions for instal
Page 30 and 31: Topaz T100siSpare partsRef. Descrip
Page 32 and 33: Topaz T100siFault Finding (continue
Page 34 and 35: Topaz T100si32
Page 36: Service PolicyIn the event of a com

Triton Topaz T100si - Faucets, Showers, Bathroom, Kitchen, More.

Create successful ePaper yourself

Delete template?

Save as template?