FlexPak 3000 Digital DC Drive Hardware ... - Reliance Electric

More documents

Recommendations

Info

Figure 2.13 – Integrator Drive Control and Power Ground Point Locations (40 to 75 HP @ 230 VAC / 75 to 150 HP @ 460 VAC)2-16 FlexPak 3000 DC Drive Hardware Reference Version 4.3
2.5.2 Recommended LugsThe following describes how to interpret lug model numbers used in grounding thedrive. Refer to table 2.2 for a list of recommended lug model and part numbers.Basic Catalog NumberNumber of Conductors1 = One conductor2 = Two conductors3 = Three conductorsMounting Hole and Lug Material1 = One mounting hole, copper2 = One mounting hole, aluminum3 = Two mounting holes, copper4 = Two mounting holes, aluminum5 = Four mopunting holes, copper6 = four mounting holes. aluminumLug Version Number01 through 991LG 1 2 03ModelNumberTable 2.2 – Recommended Lug Model and Part Numbers 1Reliance PartNumberWire SizeMountingHoleMaterial1LG1101 68321-38AA 14 - 8 AWG M5 Copper1LG1102 68321-38AB 14 - 8 AWG M6 Copper1LG1103 68321-38AC 4 - 1/0 AWG M10 Copper1LG1104 68321-38AD 1/0 - 4/0 AWG M12 Copper1LG1105 68321-38AE 4/0 - 500 MCM M10 Copper1LG1201 68321-38BA 14 - 1/0 AWG M6 Aluminum1LG1202 68321-38BB 14 - 2/0 AWG M6 Aluminum1LG1203 68321-38BC 6 - 250 MCM M8 Aluminum1LG1204 68321-38BD 6 - 300 MCM M6 Aluminum1LG1205 68321-38BE 6 - 350 MCM M10 Aluminum1LG1206 68321-38BF 4 - 500 MCM M10 Aluminum1LG1207 68321-38BG 300 - 800 MCM M12 Aluminum1LG1208 68321-38BH 500 - 1000 MCM M12 Aluminum1LG2401 68321-39BA 2 - 600 MCM M10 Aluminum1LG2402 68321-39BB 350 - 800 MCM M10 Aluminum1LG2403 68321-39BC 500 - 1000 MCM M12 Aluminum1LG3601 68321-40BA 2 - 600 MCM M12 Aluminum1.Lugs are non-insulated screw type (solderless) for use with solid and stranded wire.Install and Wire the Drive 2-17
Page 2: The information in this manual is s
Page 6: Figure 2.25 - Location of Regulator
Page 9 and 10: CHAPTER 1Introduction to the FlexPa
Page 11 and 12: The drive employs a wireless constr
Page 13 and 14: Table 1.1 - Drive Modification Kits
Page 15 and 16: CHAPTER 2Install and Wire the Drive
Page 17 and 18: Figure 2.3 - Drive Mounting Dimensi
Page 19 and 20: Figure 2.5 - Drive Mounting Dimensi
Page 21 and 22: Figure 2.7 - Integrator Drive Mount
Page 23 and 24: 2.4 Install the MotorStep 1. Verify
Page 25 and 26: Figure 2.8 - Drive Control and Powe
Page 27 and 28: Figure 2.10 - Drive Control and Pow
Page 29: Figure 2.12 - Integrator Drive Cont
Page 33 and 34: Table 2.3 - AC Line Torque Recommen
Page 35 and 36: AC LINECONNECTIONAC LINECONNECTIONS
Page 37 and 38: Figure 2.19 - DC Motor Field and Ar
Page 39 and 40: Figure 2.21 - DC Motor Field and Ar
Page 41 and 42: HorsepowerRated DrivesTable 2.4 - A
Page 43 and 44: 2.5.5.1 Wire the COAST/STOP Digital
Page 45 and 46: RS-232ConnectorFigure 2.25 - Locati
Page 47 and 48: 2.5.6.1 Logic Inputs!ATTENTION:Conn
Page 49 and 50: CHAPTER 3Drive Setup and Adjustment
Page 51 and 52: Step 4.Step 5.Re-connect power to t
Page 53 and 54: JUMPERJ15 (REGULATOR TYPE)J16 (OIM
Page 55 and 56: 3.4.3 Set Field Loss Detection (Jum
Page 57 and 58: 3.4.7 Set the Analog Auto Mode Refe
Page 59 and 60: Step 4.After power-up, select ARMAT
Page 61 and 62: CHAPTER 4Troubleshooting/Diagnostic
Page 63 and 64: 4.5 Check the Regulator LED StatusT
Page 65 and 66: CHAPTER 5Replacement Parts!ATTENTIO
Page 67 and 68: APPENDIX ATechnical SpecificationsT
Page 69 and 70: Table A.6 - Power Ratings 1 (230/46
Page 71 and 72: Table A.10 - Analog InputsManual Mo
Page 73 and 74: APPENDIX BCompliance with European
Page 75 and 76: Table B.1 - AC Mains Filter Model N
Page 77 and 78: B.3 Mounting the EquipmentMount all
Page 79 and 80: LINELOADFigure B.4 - 3DF4357 Filter
Page 81 and 82:
B.4 Grounding RequirementsStar grou
Page 83 and 84:
Main ElectricalCabinetTerminate gro
Page 85 and 86:
The external motor wiring must be r
Page 87 and 88:
ELECTRICAL CABINETAC POWERENTRYPEUV
Page 89 and 90:
APPENDIX CRecommended Parts forInte
Page 91 and 92:
AFB18818912346 5F1F2581582583Figure
Page 93 and 94:
C.2 Wire Control Power to the Drive
Page 95 and 96:
APPENDIX DGlossary Of Termsaltitude
Page 97 and 98:
service factor (SF): When used on a
Page 99 and 100:
INDEXAAC lineconnection location, 1
Page 101 and 102:
Jjumper settings, 1-4 to 1-10analog
Page 103 and 104:
DIFDocumentationImprovement FormUse
show all

FlexPak 3000 Digital DC Drive Hardware ... - Reliance Electric

Create successful ePaper yourself

Delete template?

Save as template?