FlexPak 3000 Digital DC Drive Hardware ... - Reliance Electric

More documents

Recommendations

Info

2.5.4 Wire the DC Motor to the DriveStep 1.Step 2.Step 3.Step 4.Size the motor armature circuit conductors for the specific drive rating (seeAppendix A) and according to applicable codes. Use only copper wire rated60/70°C or higher.Locate the DC motor armature and field supply leads on the drive. Refer tofigure 2.18 to 2.21.Connect the DC motor armature leads and the shunt field supply leads to thedrive. See figure 2.22.Tighten armature connections per table 2.4. Field connections should betightened to 9 lb-in (1.0 Nm). The tightening torque applies to the wiringdevice (stud or terminal board) provided. When an input or output device(breaker or lug kit) is added, refer to the kit instructions for tighteningspecifications.Figure 2.18 – DC Drive Motor Field and Armature Connection Locations(1.5 to 30 HP @ 230 VAC /3 to 60 HP @ 460 VAC / 7-110 Amp Rated Output)2-22 FlexPak 3000 DC Drive Hardware Reference Version 4.3
Figure 2.19 – DC Motor Field and Armature Connection Locations(40 to 75 HP @ 230 VAC /75 to 150 HP @ 460 VAC / 265 Amp Rated Output)Install and Wire the Drive 2-23
Page 2: The information in this manual is s
Page 6: Figure 2.25 - Location of Regulator
Page 9 and 10: CHAPTER 1Introduction to the FlexPa
Page 11 and 12: The drive employs a wireless constr
Page 13 and 14: Table 1.1 - Drive Modification Kits
Page 15 and 16: CHAPTER 2Install and Wire the Drive
Page 17 and 18: Figure 2.3 - Drive Mounting Dimensi
Page 19 and 20: Figure 2.5 - Drive Mounting Dimensi
Page 21 and 22: Figure 2.7 - Integrator Drive Mount
Page 23 and 24: 2.4 Install the MotorStep 1. Verify
Page 25 and 26: Figure 2.8 - Drive Control and Powe
Page 27 and 28: Figure 2.10 - Drive Control and Pow
Page 29 and 30: Figure 2.12 - Integrator Drive Cont
Page 31 and 32: 2.5.2 Recommended LugsThe following
Page 33 and 34: Table 2.3 - AC Line Torque Recommen
Page 35: AC LINECONNECTIONAC LINECONNECTIONS
Page 39 and 40: Figure 2.21 - DC Motor Field and Ar
Page 41 and 42: HorsepowerRated DrivesTable 2.4 - A
Page 43 and 44: 2.5.5.1 Wire the COAST/STOP Digital
Page 45 and 46: RS-232ConnectorFigure 2.25 - Locati
Page 47 and 48: 2.5.6.1 Logic Inputs!ATTENTION:Conn
Page 49 and 50: CHAPTER 3Drive Setup and Adjustment
Page 51 and 52: Step 4.Step 5.Re-connect power to t
Page 53 and 54: JUMPERJ15 (REGULATOR TYPE)J16 (OIM
Page 55 and 56: 3.4.3 Set Field Loss Detection (Jum
Page 57 and 58: 3.4.7 Set the Analog Auto Mode Refe
Page 59 and 60: Step 4.After power-up, select ARMAT
Page 61 and 62: CHAPTER 4Troubleshooting/Diagnostic
Page 63 and 64: 4.5 Check the Regulator LED StatusT
Page 65 and 66: CHAPTER 5Replacement Parts!ATTENTIO
Page 67 and 68: APPENDIX ATechnical SpecificationsT
Page 69 and 70: Table A.6 - Power Ratings 1 (230/46
Page 71 and 72: Table A.10 - Analog InputsManual Mo
Page 73 and 74: APPENDIX BCompliance with European
Page 75 and 76: Table B.1 - AC Mains Filter Model N
Page 77 and 78: B.3 Mounting the EquipmentMount all
Page 79 and 80: LINELOADFigure B.4 - 3DF4357 Filter
Page 81 and 82: B.4 Grounding RequirementsStar grou
Page 83 and 84: Main ElectricalCabinetTerminate gro
Page 85 and 86: The external motor wiring must be r
Page 87 and 88:
ELECTRICAL CABINETAC POWERENTRYPEUV
Page 89 and 90:
APPENDIX CRecommended Parts forInte
Page 91 and 92:
AFB18818912346 5F1F2581582583Figure
Page 93 and 94:
C.2 Wire Control Power to the Drive
Page 95 and 96:
APPENDIX DGlossary Of Termsaltitude
Page 97 and 98:
service factor (SF): When used on a
Page 99 and 100:
INDEXAAC lineconnection location, 1
Page 101 and 102:
Jjumper settings, 1-4 to 1-10analog
Page 103 and 104:
DIFDocumentationImprovement FormUse
show all

FlexPak 3000 Digital DC Drive Hardware ... - Reliance Electric

Create successful ePaper yourself

Delete template?

Save as template?