SIMOVERT Master Drives Einspeise-Einheit Bauform E Common ...

More documents

Recommendations

Info

02.96 Connection3.2.1 Electronic power supply / fault signalThe electronic power supply is not included in the scope of supply of the common rectifier.Plug-in terminal X9Terminal Function description perm. conductorcross-sectionX9 (mm2) (AWG)1 DC 24V (tolerance range 20V - 30V) 2)max. current consumption 2A at +24Vmax. current consumption withoutoptions: 0.3A0.2 to 2.5 24 to 14Table 3.42 Reference potential 0.2 to 2.5 24 to 143 not connected (N.C.) 0.2 to 2.5 24 to 144 Fault signal 2) 0.2 to 2.5 24 to 145 Fault signal 2) 0.2 to 2.5 24 to 14Permissible connection cross-sections for the power supply and the fault signalX9ext. SVDC 24VPMFault signal1 2 3 4 5AC 230V3000VAFigure 3.2 DC 24 V power supplyand fault signalconnectionTerminal X9.1 fused with fuse T2A/250V träge/time-lag 5x20mm(19198-T2A/250V Messrs. Wickmann-Werke GmbH respectively0034.3993 FSD Messrs. Schurter)Terminal X9.2 fused with fuse T3,2A/250V träge/time-lag 5x20mm(19198-T3,2A/250V Messrs. Wickmann-Werke GmbH respectively0034.3998 FSD Messrs. Schurter)NOTEThe exciter coil of the main contactor must be wired with surge arresters, e.g. an RC network for AC or a diodefor DC.3.2.2 Signalling relay X36 ('Warning' signal)Plug-in terminal X36Terminals Function description perm. conductorcross-section(mm2) (AWG)Table 3.5X36-1X36-2WarningSignalling contacts to switch extra-low voltage between terminals1 and 2 at a switching voltage of DC 30 V max.DC 5 A, at aswitching voltage of AC 60 V max. AC 5 A at cos 0,40,2 to 2,5 24 to 142) Contacts for switching the main contactor between terminals 4 and 5 ; switching voltage AC 230V max. AC 5A at cos 0.4; max.switching capacity 3000 VA ; at switching voltage DC 30V max. DC 8ASiemens AG 6SE7087-6AE85-0AA0 ENGLISH 3-5<strong>Common</strong> Rectifier Operating instructions
Connection 02.963.2.3 Settings on the module A23:R617: 0 resistance as earth - reference potential M connectionOn delivery, M is connected to earth. Remove this resistor only to avoid disturbances from earth loops,i.e. if the electronic reference potential is otherwise connected to earth (e.g. via the reference potentialconnection terminal of the power supply unit. The 0 resistor R210 on the A50 module must additionallybe removed when using the additional power suppy A50 (see Chapter 9.1).S500: Adjust the rated voltage range with S500 (DIP-Fix) (see Chapter 4)S1: The start-up enabling status can be switched through to the 'Warning' output (terminal X36) with S1(DIP-Fix). When S1 is open, the 'Warning' relay is opened only in the event of an excess temperature.S501: Close switch S501 only for flexible compliance (only allowed with increased pre-chokes)Works setting and normal operation = openR9between soldering terminals A and B can be removed to increase the ramp-up time from 1 to 2 seconds.3.2.4 Fan (X19)Terminals Function description perm. conductorcross-section(mm2)(AWG)X19-1 AC 230V 10%, 50 to 60Hz 5% mains connection for the fan 0,2 to 2,5 24 to 14X19-2 current consumption 0.84ATable 3.6FanTerminal X19 fused with the fuses (F3 and F4):T2A/250V time-lag 5x20mm(19198-T2A/250V Messrs. Wickmann-Werke GmbH respectively 0034.3993 FSD Messrs. Schurter)orT2A/250V time-lag 6,3x32mm (¼“ x 1¼“)(19343-T2A/250V Messrs. Wickmann-Werke GmbH respectively 0034.5231 FSD Messrs. Schurter)3-6 ENGLISH Siemens AG 6SE7087-6AE85-0AA0<strong>Common</strong> Rectifier Operating instructions
Page 1: SIMOVERT Master DrivesEinspeise-Ein
Page 4 and 5: 02.96 ContentsContentsENGLISH0 Defi
Page 6 and 7: 10.94 Definitions0 DefinitionsQUALI
Page 8 and 9: 10.94 DefinitionsWARNINGWhen operat
Page 10 and 11: 02.96 Description1 Description1.1 A
Page 12 and 13: 02.96 Transport, unpacking, assembl
Page 14 and 15: 02.96 Transport, unpacking, assembl
Page 16 and 17: 02.96 Connection3 ConnectionWARNING
Page 18 and 19: 02.96 ConnectionUnit order No.Mains
Page 22 and 23: 02.96 Connection3.3 Control termina
Page 24 and 25: 02.96 Connection3.5 Single-line dia
Page 26 and 27: 02.96 ConnectionArrangement of thyr
Page 30 and 31: 02.96 ConnectionTermal sensoron the
Page 32 and 33: 02.96 ConnectionϑR100X30-1X30-2E1M
Page 36 and 37: 02.96 Start-up4 Start-upWARNINGThe
Page 38 and 39: 02.96 Start-upRated ac-side voltage
Page 40 and 41: 02.96 Malfunctions and warnings7 Ma
Page 42 and 43: 02.96 Maintenance8 MaintenanceWARNI
Page 44 and 45: 02.96 MaintenanceReplacing modules
Page 46 and 47: 02.96 Options9 Options9.1 A50 addit
Page 48 and 49: 02.96 Options9.3 Power SupplyA SITO
Page 50 and 51: 02.96 Spare parts10 Spare partsFor
Page 52 and 53: 02.96 Environmental compatibility13
Page 54 and 55: 02.96 Technical data14 Technical da
Page 56 and 57: 02.96 Technical dataCommonrectifier
Page 58 and 59: 02.96 Technical data14.1 Power redu
Page 60 and 61: 02.96 Technical dataSourcesDIN stan
Page 62 and 63: 11.94 Index15 Indexin preparationSi
Page 64: 02.96Bisher sind folgende Ausgaben

SIMOVERT Master Drives Einspeise-Einheit Bauform E Common ...

Create successful ePaper yourself

Delete template?

Save as template?