SIMOVERT Master Drives Einspeise-Einheit Bauform E Common ...

More documents

Recommendations

Info

02.96 Maintenance8 MaintenanceWARNINGThe units SIMOVERT Master Drives are operated with high voltages.All work on the unit must be carried out in agreement with the national electrical regulations(in Germany: VBG 4).Maintenance and repair work must only be carried out by qualified personnel.Use must only be made ofd spare parts approved by the manufacturer.It is imperative to observe the prescribed maintenance intervals and the repair andreplacement instructions.Owing to the dc link capacitors, hazardous voltages still prevail in the unit up to 5 min. afterdeenergisation (power terminal and electronic power supply). This is why it is only permittedto open the unit after a corresponding waiting time.The power terminals, fan terminals and control terminals may still be live even in the evenof motor standstill.If work on the activated unit is necessary: do not touch any live parts. use only proper measuring equipment and protective work clothing. stand or sit on an unearthed and isolated surface that does justice to ESD requirements.Non-observance of warning notices can result in death, severe personal injury orconsiderable property damage.You should know the order and factory numbers of your unit when consulting the service department. You willfind these numbers and other important data on the rating plate of the unit.8.1 Maintenance recommendationsDust deposits inside the unit must be removed at least once annually by qualified personnel. If required, cleaningmust take place at shorter intervals. The unit must be cleaned with a brush and vacuum cleaner and ininaccessible locations with dust-free dry compressed air at a maximum of 1 bar.The AC-230V fan is designed for an operating life of 40 000 hours at an ambient temperature of 40 °C. It mustbe replaced in good time to maintain the availability of the unit.Siemens AG 6SE7087-6AE85-0AA0 ENGLISH 8-1Common Rectifier Operating instructions
Maintenance 02.968.2 Replacing components8.2.1 Replacing the fanWARNINGThe fan must only be replaced by qualified personnel.Owing to the dc link capacitors, a hazardous voltage prevails for a further 5 min.after deenergisation.Despite the fact that the power section is voltage-isolated, hazardous voltagesare present in the unit due to the external power supply for the fan.Non-observance of warning notices can result in death, severe personal injury orconsiderable property damage.Size EX29The fan is located on the right underside of the unit. Undo the M4 x 8/T20 Torx screw securing the fan Extract the plug-in terminal X29 Undo the M4 x 8/T20 Torx screw for earth connection Pull the fan out of the unit towards the front left Install a new fan in reverse order Before commissioning the unit, check that the fan does notrub and also check the air flow direction. The air must bedischarged from the unit in the upward direction.M4 x 8Torx T20Fan E1Figure 8.1 Fan (AC 230V) for size E8.2.2 Replacing modulesWARNINGModules must only be replaced by qualified persons.Modules must not be removed or inserted under a live voltage.Non-observance of warning notices can result in death, severe personal injury orconsiderable property damage.CAUTIONThe modules contain electrostatically sensitive devices. You must discharge your own bodybefore touching an electronic module. This is best done by touching a conductive earthedobject (e.g. a bare metal part of the control cabinet) directly beforehand.8-2 ENGLISH Siemens AG 6SE7087-6AE85-0AA0Common Rectifier Operating instructions
Page 1: SIMOVERT Master DrivesEinspeise-Ein
Page 4 and 5: 02.96 ContentsContentsENGLISH0 Defi
Page 6 and 7: 10.94 Definitions0 DefinitionsQUALI
Page 8 and 9: 10.94 DefinitionsWARNINGWhen operat
Page 10 and 11: 02.96 Description1 Description1.1 A
Page 12 and 13: 02.96 Transport, unpacking, assembl
Page 14 and 15: 02.96 Transport, unpacking, assembl
Page 16 and 17: 02.96 Connection3 ConnectionWARNING
Page 18 and 19: 02.96 ConnectionUnit order No.Mains
Page 20 and 21: 02.96 Connection3.2.1 Electronic po
Page 22 and 23: 02.96 Connection3.3 Control termina
Page 24 and 25: 02.96 Connection3.5 Single-line dia
Page 26 and 27: 02.96 ConnectionArrangement of thyr
Page 30 and 31: 02.96 ConnectionTermal sensoron the
Page 32 and 33: 02.96 ConnectionϑR100X30-1X30-2E1M
Page 36 and 37: 02.96 Start-up4 Start-upWARNINGThe
Page 38 and 39: 02.96 Start-upRated ac-side voltage
Page 40 and 41: 02.96 Malfunctions and warnings7 Ma
Page 44 and 45: 02.96 MaintenanceReplacing modules
Page 46 and 47: 02.96 Options9 Options9.1 A50 addit
Page 48 and 49: 02.96 Options9.3 Power SupplyA SITO
Page 50 and 51: 02.96 Spare parts10 Spare partsFor
Page 52 and 53: 02.96 Environmental compatibility13
Page 54 and 55: 02.96 Technical data14 Technical da
Page 56 and 57: 02.96 Technical dataCommonrectifier
Page 58 and 59: 02.96 Technical data14.1 Power redu
Page 60 and 61: 02.96 Technical dataSourcesDIN stan
Page 62 and 63: 11.94 Index15 Indexin preparationSi
Page 64: 02.96Bisher sind folgende Ausgaben

SIMOVERT Master Drives Einspeise-Einheit Bauform E Common ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?