Operating Instructions PPC-06/08-Plus v2009 (PDF - 1,3 MB) - Stauff

More documents

Recommendations

Info

$+HDY\ 7ZLQ 6HULHV Clamp Body Æ 3UR OHG 'HVLJQ ... - Stauff$

$+HDY\ 6DGGOHV DIN 1592 Dimensions / Order Codes + ... - Stauff$

Text input for UNIT / SIGNALTo set the units: Text input up to (max. 15 characters)Numerical input for FROM / TOTo set the measurement range and signal span:3-digit prefixDecimal point3-digit suffix.Measuring instrument with connector adapter and sensors for distance (mm) and force (kN).11...24VDCHandmeter11...24VDCHandmeterADCVDCADCVDC4A48V200mA 10V20mA 3V11-30VDC I1 I2 I34A48V200mA 10V20mA 3VSensorI4®PCPPC-06-plusSensorON/OFFZEROIN1=IN2STOPRECESCOKMEMSETDISPLINERESETMIN/MAX20
5.8. Error messages / WarningsDisplay Description What action to take?No sensor is connected Turn off the measuring instrumentConnect sensorTurn on the measuring instrument%An auxiliary sensor isconnectedCarry out settings in the menuSET-AUX.SENSORSensor recognitioninterrupted (cable break orinput defect)Send measuring instrument, sensor andconnection to the Walter StauffenbergGmbH & Co. KGMeasurement rangeoverflow. The measuredpressure is outside of themeasurement rangeOverflow ZEROThe zero point offset valueexceeds the toleranceOverflow IN1 = IN2Differential value alignment.The alignment valueexceeds the toleranceDISP LINE IN1 = IN2Wrong settingOverflow IN1 – IN2Differential value alignment.Wrong sensorRelease pressure from the system.Use sensor with wider measurementrange.Check only when no pressure is applied.Test system pressure.Use sensors with wider measurementrange.Configure IN1 – IN2.Measured variables (sensors) must bethe sameIN1 / IN2 = barIN1 / IN2 = l/minIN1 / IN2 = °CMeasured value memory full Download measured values to PC.Delete measured value memory.Do not use in FAST MODERecording time conflict(DURATION)FAST MODE (0,5 ms)Recording time conflict(REC RATE)Setting REC:START-STOP/POINTFAST MODE only for AUTO TRIGGERMANUAL possibleREC settingAUTO TRIGGERMANUALAlter recording time DURATIONSetting MEM-SETREC CONFIGREC RATEAlter recording interval REC RATEPress "OK" to confirm21
Page 2 and 3: Contact addressWalter Stauffenberg
Page 4 and 5: 10.0 Setting and operating via PC..
Page 6 and 7: MountingPlease abide by the instruc
Page 8: 3.0 Initial useThe measuring instru
Page 11 and 12: 4.3. Symbols and using the menusIf
Page 13 and 14: 5.1. Display format (DISP)Press DIS
Page 15 and 16: 5.3. Zero Point Calibration (ZERO)I
Page 17 and 18: 5.6. Differential value alignment (
Page 19: 5.7. Connecting auxiliary sensors (
Page 23 and 24: 6.1. Setting the units (SET-UNIT)Av
Page 25 and 26: 6.6. Setting the time / date (SET-T
Page 27 and 28: Example:No dynamic MIN-MAX values a
Page 29: 8.0 The REC menu29
Page 32 and 33: 9.2. The REC NAMES settingDesignati
Page 34 and 35: The following message is displayed:
Page 36 and 37: The data format FAST (recording int
Page 38 and 39: If conflicts arise between the reco
Page 40 and 41: If conflicts arise between the reco
Page 42 and 43: 10.0 Setting and operating via PC10
Page 44 and 45: 12.0 Technical DataSensor inputSens
Page 46 and 47: 1. Determining the number of the me
Page 48 and 49: 1. Determining the duration of the

Operating Instructions PPC-06/08-Plus v2009 (PDF - 1,3 MB) - Stauff

Create successful ePaper yourself

Delete template?

Save as template?