PSS EMP0132 A-(en) - Foxboro Eckardt

2 153DPL PSS EMP0130 A-(en)2 153DPM PSS EMP0132 A-(en)TECHNICAL DATA (acc. to IEC 770)InputStatic pressure(processpressure)........PN40(4MPa) with153DPLPN 160 1) (16 MPa), 153DPMSpan..................Infinitely variable153DPL ..............3to30mbar(0.3 to 3 kPa) or5to60mbar(0.5 to 6 kPa) or10 to 120 mbar(1 to 12 kPa)153DPM ..............40to600mbar(4 to 60 kPa) or200 to 2000 mbar(20 to 200 kPa) or800 to 5000 mbar(80 to 500 kPa)Zeroshift...............–100%to+91%ofmax.spanSetting of upperrange value .............–91%to+100%ofmax.spanMeasurementlimits.......seecharacteristics,page 4OutputRange .................0.2to1bar/3to15psi/20 to 100 kPa /0.2to1.0kp/cm 2in proportion with differentialpressureAiroutput...............max.3000 l/hAirintake...............max.2500 l/hLoad characteristic,measured at0.6bar(60kPa)..........+3%forairintake500l/h–3 % for air output 700 l/hPower supplyRated pressureof supply air .............1.4± 0.1 bar / 20 ± 1.4 psi /140 ± 10 kPaAirconsumption..........max.300l/hAmbient conditionsAmbient temperature ......–40to+125°CRelative humidity .........≤ 100 %Condensation ...........permissibleTransport and storagetemperature.............–40to+125°CProtectionclass..........IP54,IP65The device can be operated at a Class D 2 location acc. toIEC 654, Part 1.1) Up to 200 bar (20 MPa) on requestOperating conditionsStatic pressure (process pressure)153DPL ..............max.40bar(4MPa)153DPM ..............max.160bar(16MPa)Temperature of processmedium on transmitter .....–40to+125°C,temporarily (1 min)max. + 250 °C.check suitability of O-rings(see table on page 5)Dynamic behaviourStep response with connected volume (stepbetween 10 and 90 %)100 cm 3 ...............approx.2s1000 cm 3 ...............approx.2.5s3) 7)Static behaviourAccuracy 4) , zero based(including conformity,hysteresis and repeatability) . ≤±0.3 % of output spanHysteresis..............≤ 0.2 % of output spanRepeatability............≤ 0.1 % of output spanEffects of influence quantities 7)Power supply variations153DPL ..............≤ 0.2 % of output span /0.1 bar (10 kPa)153DPM ..............≤ 0.15 % of output span /0.1 bar (10 kPa)Ambient temperatureeffect 5) 6) ...............≤ 0.6 % of output span/10 Kat span ratio ≤ 2.5;≤ 0.3 % of output span/10 Kat span ratio > 2.5Static pressure (on both sides at span ratio ≥ 2.5) 6)153DPL– Lower range value .....0.25%/10bar–Span ...............0.25%/10bar153DPM– Lower range value .....0.06%/10bar–Span ...............0.06%/10bar3) Valid for measuring cells made of Mat. No. 1.45714) Conforms to accuracy acc. to ANSI / ISA-S 51.1 – 19935) Span not elevated or suppressed6) Span ratio = set span / min. span7) Double values for 153DPL-A