PSS EMP0132 A-(en) - Foxboro Eckardt

Product Specifications 06.2008 PSS EMP0132 A-(en)153DPL Pneumatic d/p Transmitter for Low Pressure153DPM Pneumatic d/p TransmitterConversion of mechanical quantities into the 0.2 to 1 bar, 3 to 10 psi or 20 to 100 kPa standard pneumatic signal forflow of liquids, vapours and gases, differential pressure and liquid levels. Also suitable for aggressive and corrosiveprocess media.FEATURES• Plus and minus side overload proof up to ratedpressure• Measuring cell is vacuum proof• Index scale to enable re-setting to a previously setspan• Zero elevation and suppression facilities can be fittedalso later• Versions for O 2 ,H 2 ,NH 3 service• Signal reversal – falling characteristic – by suppressionof zero and interchanging the plus andminus connections at the transmitter• Parts in contact with process medium made ofMat. No. 1.4571, optionally of special materials• Process temperature from –40 °C to +125 °C(–40 °F to +257 °F)• Explosion Protection II 2 G c IIC T4/T6

2 153DPL PSS EMP0130 A-(en)2 153DPM PSS EMP0132 A-(en)TECHNICAL DATA (acc. to IEC 770)InputStatic pressure(processpressure)........PN40(4MPa) with153DPLPN 160 1) (16 MPa), 153DPMSpan..................Infinitely variable153DPL ..............3to30mbar(0.3 to 3 kPa) or5to60mbar(0.5 to 6 kPa) or10 to 120 mbar(1 to 12 kPa)153DPM ..............40to600mbar(4 to 60 kPa) or200 to 2000 mbar(20 to 200 kPa) or800 to 5000 mbar(80 to 500 kPa)Zeroshift...............–100%to+91%ofmax.spanSetting of upperrange value .............–91%to+100%ofmax.spanMeasurementlimits.......seecharacteristics,page 4OutputRange .................0.2to1bar/3to15psi/20 to 100 kPa /0.2to1.0kp/cm 2in proportion with differentialpressureAiroutput...............max.3000 l/hAirintake...............max.2500 l/hLoad characteristic,measured at0.6bar(60kPa)..........+3%forairintake500l/h–3 % for air output 700 l/hPower supplyRated pressureof supply air .............1.4± 0.1 bar / 20 ± 1.4 psi /140 ± 10 kPaAirconsumption..........max.300l/hAmbient conditionsAmbient temperature ......–40to+125°CRelative humidity .........≤ 100 %Condensation ...........permissibleTransport and storagetemperature.............–40to+125°CProtectionclass..........IP54,IP65The device can be operated at a Class D 2 location acc. toIEC 654, Part 1.1) Up to 200 bar (20 MPa) on requestOperating conditionsStatic pressure (process pressure)153DPL ..............max.40bar(4MPa)153DPM ..............max.160bar(16MPa)Temperature of processmedium on transmitter .....–40to+125°C,temporarily (1 min)max. + 250 °C.check suitability of O-rings(see table on page 5)Dynamic behaviourStep response with connected volume (stepbetween 10 and 90 %)100 cm 3 ...............approx.2s1000 cm 3 ...............approx.2.5s3) 7)Static behaviourAccuracy 4) , zero based(including conformity,hysteresis and repeatability) . ≤±0.3 % of output spanHysteresis..............≤ 0.2 % of output spanRepeatability............≤ 0.1 % of output spanEffects of influence quantities 7)Power supply variations153DPL ..............≤ 0.2 % of output span /0.1 bar (10 kPa)153DPM ..............≤ 0.15 % of output span /0.1 bar (10 kPa)Ambient temperatureeffect 5) 6) ...............≤ 0.6 % of output span/10 Kat span ratio ≤ 2.5;≤ 0.3 % of output span/10 Kat span ratio > 2.5Static pressure (on both sides at span ratio ≥ 2.5) 6)153DPL– Lower range value .....0.25%/10bar–Span ...............0.25%/10bar153DPM– Lower range value .....0.06%/10bar–Span ...............0.06%/10bar3) Valid for measuring cells made of Mat. No. 1.45714) Conforms to accuracy acc. to ANSI / ISA-S 51.1 – 19935) Span not elevated or suppressed6) Span ratio = set span / min. span7) Double values for 153DPL-A

PSS EMP0130 A-(en) 153DPL 3PSS EMP0132 A-(en) 153DPM 3MaterialsMeasuring cell andforce beam. .............Mat.No.1.4571, optionallyHastelloy B, Hastelloy C,Monel, Inconel(see also table on page 5 andModel Codes)Force beam seal .........Duratherm600, optionallyHastelloy B, Hastelloy C,Tantalum-Wolfram(see also table on page 5and Model Codes)Cell filling ...............Silicone oil (Fluorolubeon request)Body..................optionally Mat. No. 1.4571,steel, galvanized orspecial materialNuts and bolts for bodymade of steel withtemperature range 1)–10to+125°C.........8.8/8made of steel withtemperature range 1)–40 to –10 °C (+125 °C) . . Stainless steel A2 / A4(additional equipment)made of Mat. No. 1.4571or special material withtemperature range 1)–40to+125°C.........Stainless steel A2 / A4Seals in contactwith process medium ......FPM,e.g.Viton(Standard),optional NBR, CR,e.g. Perbunan, PTFE, EPDM(see also table on page 5)Cover..................Plastic,glass-fibre reinforcedMountingMounting type ...........wall/pipemountingNominalposition .........horizontaldiaphragm axis,any inclination with respect tothe horizontal diaphragm axisProductconnections.......Connectiondimensionsacc.to DIN 19 213 - A 1 withadditional female thread1 / 4 – 18 NPT for direct screwconnection of drain plugs andcompression fittingsPneumatic connections ....Femalethread 1 / 4 –18NPTWeight153DPL ................approx.11.3kg153DPM ...............approx. 8.2kgChangeover valve ........approx. 2.3kgManifold valve ...........approx. 3.0kg1) Temperature of process medium in transmitter

4 153DPL PSS EMP0130 A-(en)4 153DPM PSS EMP0132 A-(en)Characteristics with measurement limits= minimum span= maximum spanOutputThe maximum span which can be set at thetransmitter is also the measurement limit for themeasuring cell.max. suppressionlower measurementlimit of measuring cellmax. elevationupper measurementlimit of measuring cellmin.spanInputThus when the zero is elevated the following mustapply:Elevation + set span ≤ measurement limit.SAFETY REQUIREMENTS 1)For special applications:Application in Zone 0application in Zone 0 is possible at condition to respect thespecifications explained in the certificate BF 629TypeBF629............01/PTB/IIIB/S1507Wasserstand 100/3According to VdTÜV-Merkblatt 254 usable as secondwater level transducer, subject to license.Component identification ...TÜV.WRS.94-2541) Only with appropriate order. National regulations are to be obeyed.

PSS EMP0130 A-(en) 153DPL 5PSS EMP0132 A-(en) 153DPM 5MATERIALSMeasuring cell, body, force beam and force beam sealShortname Mat. No. DIN Notes Conformity ASTMX 6 CrNiMoTi 17 122 1.4571 17 440 Austenitic steel ~ TP 316 TiNiMo 28 2.4617 17 744 = Hastelloy B-2 VdTÜV-Wbl. 436 UNS N10665NiMo 16 Cr 16 Ti 2.4610 17 744= Hastelloy C-4 VdTÜV-Wbl.424UNS N06022NiCr 15 Fe 2.4816 17 742 Inconel 600 UNS N06600NiCu 30 Fe 2.4360 17 743 Monel 400 UNS N04400Ta-WTantalum-WolframC 22.8 1.0460 17 243 VdTÜV-Wbl. 350/3 A 576-1020Duratherm 600: 40 Co, 26 Ni, 12 Cr, Mo, W, Ti, Al, FeBolts and nutsA2 / A4 267 Part 13 Bolts and nuts–40 to –10 °C (+125 °C) **8.8 / 8 267 Part 13 Bolts and nuts–10 to +125 °C **** Temperature of process medium in transmitterA193B8M/A194B8MA193B7M/A194Gr7O-RingsThe O-Ring material must be chosen with regard to the chemicals beingprocessed, and the working temperature.ColourTemperature rangeFluorocaoutchouc (FPM), e.g. Viton (Standard version) green –25 to +125 °C **Elastomer (NBR, CR), e.g. Perbunan (option) black –40 to + 80 °CPTFE * (option) white –40 to +125 °C **EPDM for ammonia NH3 (option) black –40 to +125 °C* If the temperature of the process medium sinks to lower values, sealing problems may result.** Temperature of process medium in transmitter

6 153DPL PSS EMP0130 A-(en)6 153DPM PSS EMP0132 A-(en)MODEL CODES 153DPLPneumatic Low Differential Pressure Transmitter 153DPL 010408Span LimitskPa inch H 2O mbar0.3&3.0 1.2&12 3&30 . . . . . . . . . . . . . . . . . . -A0.5&6.0 2 &24 5&60 . . . . . . . . . . . . . . . . . . -B1.0&12 4 &48 10&120. . . . . . . . . . . . . . . . . . -CSignal Range0.2to1.0bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13to15psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220to100kPa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.2to1.0kp/cm². . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body MaterialCarbonSteel(PNmax.40bar) . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4571 (316 Ti) (PN max. 40 bar) . . . . . . . . . . . . . . . . . . . . . . . . . . 2Material of Measuring cell + force beam1.4571 (316Ti) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Sensor Fill FluidSilicone Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Inert Fill Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Sensor O-Ring Material & their Temp. LimitsFPM; -25to+120°C; -13to+250°F(Viton) . . . . . . . . . . . . . . . . . . . . . . . . . . . . VNBR;CR; -40to+80°C; -40to+175°F(BunaN). . . . . . . . . . . . . . . . . . . . . . . . . . . BPTFE; -40to+120°C; -40to+250°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PEPDM; -40to+120°C; -40to+250°F (b) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EProcess connection1/4 - 18 NPT (DIN 19213-A 100-M10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1OptionsZero Elevation or Suppression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -ANuts and bolts in stainless steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -DFor oxygen service cleaned (only with fillfluid 2 and with Body material 2). . . . . . . . . . . . . . . . . . . . . . . . -OVersion for H 2, (only with fillfluid 2 and with Body material 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -HProtectionclassIP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -PGerman National licensesSafety device against detonation (Material 1.4571 and 1.4410) Connection: internal thread G ¼ . . . . . . . . . . . . -FCertificatesEN 10204-2.1 (DIN 50 049-2.1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1EN 10204-2.3 (DIN 50 049-2.3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2Wasserstand100/3 (g) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9Tag.No. LabelingStainless steel label fixed with wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -Lcontinued on next page

PSS EMP0130 A-(en) 153DPL 7PSS EMP0132 A-(en) 153DPM 7Product Connect. Flange Set see EMP9031Compression Fittings see EMP9031Manifold Valve see EMP9032Changeover Valve see EMP9032Tube Fittings see EOO9001Mounting Kit see EMP9031Example: 153DPL -A 1 2 1 1 V 1 -ASFootnotes(a) Available with Span Limit C and Body Material Code 2 only(b) Use for ammonia, NH 3(e) Not available with Span Limits -A, only with Cell Material 1, only with Sensor O-Ring V, only with Option -F(g) On request

8 153DPL PSS EMP0130 A-(en)8 153DPM PSS EMP0132 A-(en)MODEL CODES 153DPMPneumatic Differential Pressure Transmitter 153DPM 010408Span LimitskPa inch H 2O mbar4&60 16&240 40&600 . . . . . . . . . . . . . . . . . -D20 & 200 80 & 800 200 & 2000. . . . . . . . . . . . . . . . . -E80 & 500 320 & 2000 800 & 5000. . . . . . . . . . . . . . . . . -FSignal Range0.2to1.0bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13to15psi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220to100kPa . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30.2to1.0kp/cm². . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body MaterialCarbonSteel(PNmax.160bar) . . . . . . . . . . . . . . . . . . . . . . . . . . 11.4571 (316 SS) (PN max. 160 bar) . . . . . . . . . . . . . . . . . . . . . . . . . 2Material of Measuring cell + force beam1.4571 (316Ti) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Sensor Fill FluidSilicone Oil (Standard). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Inert Fill Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Sensor O-Ring Material & their Temp. LimitsFPM; -25to+120°C;-13to+250°F(Viton). . . . . . . . . . . . . . . . . . . . . . . . . . . . . VNBR;CR; -40to+80°C; -40to+175°F(BunaN) . . . . . . . . . . . . . . . . . . . . . . . . . . . BPTFE; -40to+120°C;-40to+250°F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PEPDM; -40to+120°C;-40to+250°F (a). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EProcess Connection1/4 - 18 NPT (DIN 19213-A 100-M10) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1OptionsZero Elevation or Suppression for span Limit D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -AZero Elevation or Suppression for span Limit E, F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -BNuts and bolts in stainless steel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -DFor oxygen service cleaned (only with fillfluid 2 and with Body material 2). . . . . . . . . . . . . . . . . . . . . . . . -OVersion for H 2 (only with fillfluid 2 and with Body material 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -HProtectionclassIP65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -PGerman National licensesSafety device against detonation (Material 1.4571 and 1.4410) Connection: internal thread G ¼ . . . . . . . . . . . . -FCertificatesEN 10204-2.1 (DIN 50 049-2.1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -1EN 10204-2.3 (DIN 50 049-2.3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -2Wasserstand100/3 (f). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -9Tag.No. LabelingStainless steel label fixed with wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -Lcontinued on next page

PSS EMP0130 A-(en) 153DPL 9PSS EMP0132 A-(en) 153DPM 9Product Connect. Flange Set see EMP9031Compression Fittings see EMP9031Manifold Valve see EMP9032Changeover Valve see EMP9032Tube Fittings see EOO9001Mounting Kit see EMP9031Example: 153DPM -D 1 2 1 1 V 1 -ASFootnotes(a) Use for ammonia, NH 3(d) Available with Body Material 1& 2, only with Cell Material 1, only with Sensor O-Ring V, only with Option -F(f) On request

10 153DPL PSS EMP0130 A-(en)10 153DPM PSS EMP0132 A-(en)DIMENSIONSTransmitter 153DPLall dimensions in mmTransmitter 153DPMall dimensions in mm1 Supply air2 Output signal3 Product connectionsConnection dimensions as per DIN 19 213 - A1 withadditional female thread 1 / 4 – 18 NPT for direct screwconnection of drain plugs and compression fittings4 Drain or vent plugs 1 / 4 –18NPT5 Adapter flanges (additional equipment) with hexagonsocket screws M10 x 35 – 8.8. Connection dimensionsas per DIN 19 213 - B1, optionally with femalethread 3 / 8 –18NPTor 1 / 2 – 14 NPT (USA B 2.1)6 Female glands (additional equipment) with solderlesscompression fitting as per DIN 2353 either3 / 8 – 18 NPT / DS 12 for pipes 12 x 1.5 DIN 19 210 or1 / 2 – 14 NPT / DS 12 for pipes 12 x 1.5 DIN 19 2107 Pipe mounting kit

PSS EMP0130 A-(en) 153DPL 11PSS EMP0132 A-(en) 153DPM 11Transmitter with changeover valve (additional equipment)all dimensions in mmFunctions of thechangeover valvefrom measuring pointTest Operation Line 2 Line 1(venting) (venting)to transmitter* Dimensions with transmitter 153DPL** Dimensions with transmitter 153DPMTransmitter with manifold valve (additional equipment)all dimensions in mmFunctions of the manifold valvefrom measuring pointBalancing Test Operationto transmitter* Dimensions with transmitter 153DPL** Dimensions with transmitter 153DPM1 Pneumatic differential pressure transmitter2 Changeover valve PN 100 (10 MPa) with zero balancingand vent connection as per serial No. 11, DIN 19 209,with mounting kit3 Vent connection4 Female glands with solderless compression fitting as perDIN2353G 3 / 8 A / DS 12 for pipes 12 x 1.5 DIN 19 2105 Pipe and wall mounting kit6 Manifold valve PN 160 (16 MPa) as per serial No. 9,DIN 19 209, with mounting kit

12 153DPL PSS EMP0130 A-(en)12 153DPM PSS EMP0132 A-(en)*Subject to alterations - reprinting, copying and translation prohibited. Products and publications arenormally quoted here without reference to existing patents, registered utility models or trademarks.The lack of any such reference does not justify the assumption that a product or symbol is free.FOXBORO ECKARDT GmbHPostfach 50 03 47D-70333 StuttgartTel. # 49(0)711 502-0Fax # 49(0)711 502-597http:\\www.foxboro-eckardt.com DOKT 535 701 028