BRAKES & CLUTCHES

Disassembly & Assembly Instructions
96
Assembly
1. Replace parts as needed.
2. Install the collar assembly over the output shaft and spring assembly. (Pull
the brake spring through the collar with needle-nosed pliers, taking care not
to distort the spring.)
3. Install the output shaft and collar assembly on the mounting plate – turn in
direction of rotation only.
4. Install the retaining ring on the mounting plate end with its
smooth surface facing the brake hub.
5. Install the input hub and reset spring differential as needed (CB-10). Install
the input hub with thrust washer flange oriented correctly and reset the
spring differential as needed (Super CB-10). (See “CB Spring Differential
Adjustments”on page 90.)
6. Install the retaining ring with smooth surface facing the hub.
SAC-2, -4 and -5
Disassembly
1. Remove the retaining ring from the input hub end.
2. Remove input hub – turn in direction of rotation only.
3. Remove the stop collar by extracting the collar toward the clutch spring end.
Assembly
1. Replace parts as needed.
2. Install the stop collar over the output shaft and spring assembly. (Pull the
clutch spring tang through the collar with needle-nosed pliers, taking care
not to distort the spring.)
3. Install input hub – turn in direction of rotation only.
4. Install retaining ring.
SAC-6
Disassembly
1. Remove the retaining ring from the input hub end.
2. Remove input hub – turn in direction of rotation only.
3. Remove the retaining ring from the mounting plate end.
4. Remove the output shaft and stop collar assembly from the mounting plate
– turn in the direction of rotation only. Do not remove plate hub from
mounting plate.
5. Remove the control stop from the output shaft by extracting the collar
towards plate side of the output shaft.
Assembly
1. Replace parts as needed.
2. Install the stop collar over the output shaft and spring assembly.
3. Install the output shaft and stop collar assembly on the mounting plate –
turn in direction of rotation only.
4. Install the retaining ring to output shaft.
5. Install the input hub.
6. Install the retaining ring on the shaft input end.
ACCE
Disassembly
1. Remove spiral ring and thrust washer from both ends of the shaft.
2. Rotate clutch and remove it from the plate. Remove the large thrust washer.
3. For shaft input units, remove the shaft assembly by rotating opposite to
drive direction.
4. For hub input units, remove the hub by rotating opposite to drive direction.
5. For Model SS, remove the stop collar and spring by rotating opposite to drive
direction and pulling the drive spring off the output hub.
6. For Model S, pull the stop collar axially to release it from the spring. Rotate
the spring opposite to drive direction until the down tang can be pried from
its hole.
Assembly
1. For Model S, assemble spring to output hub by rotating opposite to drive
direction until the down tang is seated in the hole.
Tel
: 540 633 3400 Web site : www.DanaherMotion.com
Deltran PT
Brakes & Clutches
2. For Model SS, assemble spring to output hub by rotating opposite to drive
direction until the spring is seated against the large retaining ring.
3. Assemble stop collar over spring by deflecting the input tang with long-nose
pliers (reach through the collar with the pliers).
4. Assemble input by rotating opposite to drive direction.
5. Install large thrust washer and slide clutch assembly onto the plate.
6. Install thrust washers and spiral rings on both ends of the shaft.
ACCM
Disassembly
1. Remove spiral ring and thrust washer from the shaft.
2. For shaft input units, remove the shaft assembly by rotating opposite to
drive direction.
3. For hub input units, remove the hub by rotating opposite to drive direction.
4. For Model SS, remove the stop collar and spring by rotating opposite to drive
direction and pulling the drive spring off the output hub.
5. For Model S, pull the stop collar axially to release it from the spring. Rotate
the spring opposite to drive direction until the down tang can be pried from
its hole.
Assembly
1. For Model S, assemble spring to output hub by rotating opposite to drive
direction until the down tang is seated in the hole.
2. For Model SS, assemble spring to output hub by rotating opposite to drive
direction until the spring is seated against the large retaining ring.
3. Assemble stop collar over spring by deflecting the input tang with long-nose
pliers (reach through the collar with the pliers).
4. Assemble input by rotating opposite to drive direction.
5. Install thrust washer and spiral ring on the shaft.
PSI
Disassembly
1. Remove retaining ring from shaft.
2. Remove hub end by rotating opposite to drive direction.
3. For Model S, remove stop collar and spring by rotating opposite to drive
direction and pulling to remove output tang from hub.
Assembly Model S
1. Assemble spring to output hub by rotating opposite to direction of rotation.
Output tang must be inserted completely into hole in hub during this assembly.
2. Assemble stop collar over spring by deflecting input tang with long-nose pliers.
(Reach through collar with pliers.)
3. Assemble input hub by rotating opposite to direction of rotation.
4. Assemble retaining ring to shaft.
Assembly Model O & SS
1. Assemble spring and stop collar (or sleeve) with control tang located in slot
in collar.
2. Assemble spring and collar to output hub by rotating opposite to direction
of rotation.
3. Assemble input hub by rotating opposite to direction of rotation.
4. Assemble retaining ring to shaft.
DANAHER MOTION is a registered trademark of Danaher Corporation. Danaher Motion makes every attempt to ensure accuracy and reliability of the specifications in this publication. Specifications are subject to change without notice. Danaher Motion provides this information "AS IS" and
disclaims all warranties, express or implied, including, but not limited to, implied warranties of merchantability and fitness for a particular purpose.It is the responsibility of the product user to determine the suitability of this product for a specific application. ©2004 Danaher Motion.