Digital Photoelectric Sensor PS-N10 Series Instruction Manual ...

More documents

Recommendations

Info

Specifications• Transparent Sensor HeadsThru-beam typeTypeGeneral-purposeEnvironmentally resistant typeLong distance Adjustable axis Cylinder Flat Long distance Built-in grooveModel *1 PS-55(C) PS-05 PS-58 PS-52(C) PS-56 PS-201(C) PS-202MEGA 3600 (6000) 3600 (6000) 1000 1200 (1500) 750 (900) 3600 (6000) 900 (1000)DetectionULTRA 2800 (5000) 2800 (5000) 900 800 (1000) 500 (600) 2800 (5000) 700 (900)distance *2(mm)SUPER 2200 (4200) 2200 (4200) 750 400 (650) 400 (450) 2200 (4200) 600 (800)TURBO 2000 (4000) 2000 (4000) 700 300 (600) 300 (400) 2000 (4000) 500 (750)Smallest detectableobject *3 Ф 1 mm opaque Ф 0.5 mm opaque Ф 0.3 mm opaque Ф 0.3 mm opaque Ф 0.8 mm opaque Ф 0.5 mm opaqueEnvironmentalresistanceLight sourceLED ClassProtectionstructureOperatingambienttemperatureOperatingambientluminanceVibrationresistanceWeight(2 m cable included)Infrared LEDClass 1 LED Product (IEC60825-1)IP64 IP67 - IP67-10ºC to +60ºC (no freezing)Incandescent lamp: 4,000 lx or less; sunlight: 12,000 lx or less10 to 55 Hz, compound amplitude 1.5 mm, 2 hours for each axis (X, Y, and Z)Approx. 30 g Approx. 30 g Approx. 30 g Approx. 30 g Approx. 30 g Approx. 40 g Approx. 40 g*1 A sensor head connector is attached to the end of the cable for the sensor heads with model names containing the suffix C.*2 The values in parentheses indicate the detection distance when long-distance detection mode is enabled and a 5 m sensor head cable is used.*3 The size of a workpiece that can be detected at the maximum detection distance.• Reflective Sensor HeadsDiffuse reflective typeLimited reflective typeTypeGeneral-purpose Environmentally resistant General-purposeLong distance Flat Cylinder Long distance Narrow vision Small spot Long distanceModel *1 PS-45 PS-46 PS-48 PS-205 PS-206 PS-47(C) PS-49(C)MEGA 600 (900) 200 (250) 75 600 (900) 250DetectionULTRA 400 (600) 150 (200) 45 400 (600) 180distance *2(mm)SUPER 250 (450) 120 (160) 30 250 (450) 10010μ4 32 to 53TURBO 200 (400) 100 (140) 25 200 (400) 70Smallest detectableobject *3 φ- - φ- - -EnvironmentalresistanceSpot diameter - - - -Ф 6 mmwhen the detectiondistance is 70 mmФ 0.03 mm copperwireФ 8 mmwhen the detectiondistance is 10 mmLight source Infrared LED Red LEDLED ClassClass 1 LED Product (IEC60825-1)ProtectionstructureIP64 - IP67 -OperatingambienttemperatureOperatingambientluminanceVibrationresistanceWeight(2 m cable included)-10ºC to +60ºC (no freezing)Incandescent lamp: 4,000 lx or less; sunlight: 12,000 lx or less10 to 55 Hz, compound amplitude 1.5 mm, 2 hours for each axis (X, Y, and Z)Ф 0.1 mm copperwireФ 1.5 mmwhen the detectiondistance is 50 mm-10ºC to +50ºC(no freezing)Incandescent lamp: 4,000 lx or less; sunlight:5,000 lx or lessApprox. 30 g Approx. 30 g Approx. 40 g Approx. 60 g Approx. 60 g Approx. 30 g Approx. 30 g*1 There is a sensor head connector attached to the end of the cable for the sensor heads with model names containing the suffix C.*2 The values in parentheses indicate the detection distance when long-distance detection mode is enabled.*3 The values obtained by optimizing the detection distance and sensitivity.10
• Sensor AmplifierCable / Connector Cable M8 Connector 0-lineMain unit / Expansion unit Main unit Expansion unit Main unit Expansion unit Expansion unitModelControl outputNPN PS-N11N PS-N12N PS-N11CN PS-N12CNPNP PS-N11P PS-N12P PS-N11CP PS-N12CPControl output 1 output 1 output 1 output 1 output N/A *1External input 1 input N/A 1 input 1 input N/AResponse timeOutput operationTimer functionNPN outputPNP output500 μs (TURBO)/1 ms (SUPER)/4 ms (ULTRA)/16 ms (MEGA)Light-ON/Dark-ONTimer OFF, OFF delay, ON delay, One-shotTimer variable (1 ms to 9999 ms) Maximum error to setting value is μ10 % or less*1 Counted as one output when units are added to NU series communication units.*2 Input time is 25 ms (ON)/25 ms (OFF) only when an external tuning input is selected.*3 The operating ambient temperature varies as shown below when units are added. For expansion, be sure to mount the units on the DIN rail (metallic plate) andprevent the output current for each unit from exceeding 20 mA.- 20ºC to + 55ºC for 1 or 2 units added, - 20ºC to + 50ºC for 3 to 10 units added, - 20ºC to + 45ºC for 11 to 16 units added*4 When connecting nine or more expansion units, ensure that the power voltage is 20 V or more.*5 The maximum power consumption including load is 29.3 W.*6 Use with the over current protection device which is rated 30 V or more and not more than 1 A.PS-N10NPN open collector 30 V, Max: 100 mA or less (for standalone operation)/20 mA or less (for expansion)Residual voltage 1 V or less (Output current: 10 mA or less)/2 V or less (Output current: 10 to 100 mA)PNP open collector 30 V, Max: 100 mA or less (standalone operation)/20 mA or less (for expansion)Residual voltage 1.2 V or less (Output current: 10 mA or less)/2.2 V or less (Output current: 10 to 100 mA)External input No-voltage input (with/without contact), Input time 2 ms (ON)/20 ms (OFF) or more *2Expansion unitsProtection circuitNumber of interference prevention unitsRatedEnvironmentalresistanceMaterialHousing dimensionsPower voltage *4Up to 16 units (a total of 17 units connected)Protection against reverse power connection, output overcurrent, output surge, and output wiring errorTURBO/SUPER/ULTRA/MEGA: 4 (These numbers double when "Double" is selected.)24 VDC (operating voltage 10-30 VDC (including ripple)), ripple (P-P) 10 % or less, Class 2 or LPSNormal: 810 mW or less (28 mA or less at 24 and 30 V, 34 mA or less at 12 V)NPN *5 Eco on: 700 mW or less (24 mA or less at 24 and 30 V, 27 mA or less at 12 V)Eco full: 490 mW or less (17 mA or less at 24 and 30 V, 20 mA or less at 12 V)Normal: 860 mW or less (30 mA or less at 24 and 30 V, 35 mA or less at 12 V)PNP *5 Eco on: 750 mW or less (26 mA or less at 24 and 30 V, 28 mA or less at 12 V)Eco full: 540 mW or less (19 mA or less at 24 and 30 V, 21 mA or less at 12 V)Operating ambient- 20°ºC to + 55°ºC (no freezing)temperature*3Operating ambienthumidityVibration resistanceShock resistanceHousingCable35 to 85 % RH (no condensation)10 to 55 Hz, compound amplitude 1.5 mm, 2 hours for each of X, Y, Z axes500 m/s 2 , 3 times for each of X, Y, Z axesAmplifier body and dust cover material: PolycarbonatePVCH 32.6 mm x W 9.8 mm x L 78.7 mmWeight Approx. 75 g Approx. 65 g Approx. 20 g Approx. 20 g Approx. 20 g11
Page 1 and 2: 96M11680Precautions on Regulations
Page 3 and 4: PS-N10 Series Quick StartConnecting
Page 5: Connecting Multiple AmplifiersOther
Page 8 and 9: Function Configuration• Display S
Page 12: WARRANTIES AND DISCLAIMERS(1) KEYEN

Digital Photoelectric Sensor PS-N10 Series Instruction Manual ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?