Digital Photoelectric Sensor PS-N10 Series Instruction Manual ...

More documents

Recommendations

Info

• Sensor Head• PS-45Mounting bracket set• PS-46ReceiverReceiverTransmitterMounting bracket x 1Plate nut x 1M3 x 12 screw x2TransmitterNut x 2Spring washer x 2Flat washer x 2M2 x 10 screw x 2• PS-47/PS-47C* 1 Transmitter• PS-48Mounting bracket x 1ReceiverReceiverTransmitter• PS-49/PS-49C* 1 Transmitter• PS-05Transmitter (T)Receiver (R)ReceiverNut x 2Spring washer x 2Flat washer x 2M3 x 14 screw x 2For fixing the headHolderSpring washer x 4M3 x 10 screw x 4For fixing the holder• PS-52/PS-52C* 1 Transmitter (T)• PS-55/PS-55C* 1 Transmitter (T) Receiver (R)Receiver (R)Nut x 4Spring washer x 4Flat washer x 4M2 x 10 screw x 4• PS-56• PS-58Transmitter (T)Receiver (R)Transmitter (T) Receiver (R) Mounting bracket x 2Nut x 4Spring washer x 4Flat washer x 4M2 x 10 screw x 4• PS-201/PS-201C* 1• PS-202Transmitter(T) Receiver (R) Mounting bracket x 2Transmitter (T) Receiver (R) Mounting bracket x 2• PS-205• PS-206ReceiverReceiverTransmitterTransmitter*1 A sensor head connector is attached to the end of the cable for the sensor heads with model names containing the suffix C.2
PS-N10 Series Quick StartConnecting the Sensor Head to the Sensor Amplifier• Quick StartFine sensitivity adjustmentUpDownMode/Output * 2Press the [MODE] button once, thenuse to select L-on or D-on• Installing the Sensor Head Connector1 Process the cable ends as shown below. The core wire conductors are stripped sothat they are exposed at the time of shipment. Be sure to process the cables withoutremoving the insulation from the cable ends.Preset functionSetting value Light intensitySensitivity settingPress once each for workpiece/no workpieceSELMPower select switch * 1SELStandard MEGA (fixed)MConfigure easilywith a single presswhen receiving light10 mm or longerShielded wireCablecore2 Move the upper left part of the connector in the direction of the arrow and then openthe connector.*1 Not available for 0-line types.*2 Press and hold the [MODE] button to make advanced setting changes.Names of Each Part of the Main Unit and Expansion UnitHead lock lever3 Fully insert the cables with the shielded wires standing upright. Next, bend theshielded wires along the grooves in the direction of the arrow.SET button (SET)Operation status indicatorsPST indicatorDTM indicatorDigital displayManual button( )Sub screen(Displayed in green)Main screen(Displayed in red)White wireRed wire4 Close the connector to crimp the cables. Return the upper part of the connector to itsoriginal position and then lock it.Powerselection switchMODE button (MODE)Cable*Dust coverExpansionprotective coverExpansion connectorPreset button (PRESET)Power select switch5 Using nippers, cut off the ends of cables protruding from the connector.* On the PS-N11Cx / N12Cx, this is an M8 connector rather than a cable. Not available for 0-linetypes.Mounting Unit• Mounting on a DIN Rail1 Align the claw at the bottom of the main bodywith the DIN rail, as shown on the right.While pushing the main body in the directionof the arrow 1, push down in the direction ofarrow 2.2 To dismount the sensor, raise the main bodyin the direction of the arrow 3 while pushingthe main body in the direction of arrow 1.321NOTICECrimp the cables no more than three times. Excessively crimping thecables may result in a bad connection.• Connecting the Sensor Head1 Open the dust cover, and move thehead lock lever down.• Installation on a Wall (Main Unit Only)1 Attach the unit to the optional mountingbracket (OP-73880), and secure with two M3screws as shown on the right.2 Lift the hook up, and insert the connectorcompletely.3 Lower the hook to theposition shown in thedrawing, and securethe head lock lever bypushing up.3
Page 1: 96M11680Precautions on Regulations
Page 5: Connecting Multiple AmplifiersOther
Page 8 and 9: Function Configuration• Display S
Page 10 and 11: Specifications• Transparent Senso
Page 12: WARRANTIES AND DISCLAIMERS(1) KEYEN

Digital Photoelectric Sensor PS-N10 Series Instruction Manual ...

Create successful ePaper yourself

Delete template?

Save as template?