User Manual - ALLSEASONS Heating And Cooling

More documents

Recommendations

Info

24TROUBLE SHOOTING GUIDEBEFORE ATTEMPTING TO TROUBLESHOOT, PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR REMOVED.SYMPTOM PROBLEM TEST SOLUTIONPilot will not light.Pilot goes out whenthe gas knob is released.Pilot burning; nogas to mainburner; gas knobis on 'HI'; wallswitch / thermostatis on.Pilot goes out whilestanding; Mainburner is in 'OFF'position.Main burner goesout; pilot stays on.W415-0496 / B / 08.10.05No spark at pilot burnerSpark gap is incorrectNo gas at the pilot burnerOut of propane gas.System is not correctly purged.Out of propane gasPilot flame is not large enoughPilot flame is not engulfing thethermocouple.Thermocouple shorting.Faultly thermocouple.Faulty valve.Main burner orifice is plugged.Faulty thermopile.Faulty themostat or switch.Faulty valve.Gas piping is undersized.Pilot flame is not large enoughor not engulfing the thermopile.Thermopile shortingRemote wall switch wire is toolong, too much resistance inthe systemFaulty thermostat or switch- check if pilot can be lit by a match- check that the wire is connected to the push button ignitor.- check if the push button ignitor needs tightening.- replace the wire if the wire insulation is broken or frayed.- replace the electrode if the ceramic insulator is cracked orbroken.- spark gap should be 0.150" to 0.175" (5/32" to 11/64" approx.)from the electrode tip and the pilot burner. To ensure properelectrode location, tighten securing nut (finger tight plus 1/4turn).- check that the manual valve is turned on.- check the pilot orifice for blockage.- replace the valve.- call the gas distributor.- fill the tank.- purge the gas line with the stove door open.- fill the tank.- turn up the pilot flame.- turn up pilot flame.- replace pilot assembly.- loosen and tighten thermocouple.- clean thermocouple and valve connection.- replace thermocouple.- replace valve.- replace.- replace.- remove stoppage in orifice.- replace.- connect a jumper wire across the wall switch terminals; ifmain burner lights, replace thermostat.- disconnect switch wires from the valve & connect a jumperwire across terminals 1 & 3; if the main burner lights, check thewires for defects and / or replace wires.- disconnect the pilot light wires from the valve and connect ajumper wire across terminals 1 & 3; if the main burner lights,check the wires for defects and / or replace wires.- replace.- turn on all gas appliances and see if pilot flame flutters,diminishes or extinguishes, especially when main burner ignites.Monitor supply pressure.- check if supply piping size is to code. Correct all undersizedpiping.- turn up pilot flame.- replace pilot assembly.- clean thermopile and thermopile connection to valve.- shorten wire to correct length or wire gauge.- replace
25SYMPTOM PROBLEM TEST SOLUTIONMain burner goes out;pilot goes out.REFER TO "MAIN BURNER GOES OUT; PILOT STAYS ON"Vent re-circulating- check joint seals and installation.Exhaust fumessmelled in room,headaches.Carbon is being depositedon glass, logsor combustion chambersurfaces.Flames are veryaggressive.Thermocouple shorting orfaulty.Fireplace is spilling.Air shutter has becomeblockedFlame is impinging on thelogs or combustion chamber.Door is ajarVenting action is too great.- loosen and tighten thermocouple- clean thermocouple and valve connection.- replace thermocouple.- replace valve.- check all seals.- ensure air shutter opening is free of lint or other obstructions.- check that the logs are correctly positioned.- open air shutter to increase the primary air.- check the input rate: check the manifold pressure and orificesize as specified by the rating plate values.- check that the door gasketing is not broken or missing andthat the seal is tight.- check that both vent liners are free of holes and well sealed atall joints.- check that minimum rise per foot has been adhered to for anyhorizontal venting.- tighten door clamps- restrict vent exit with restrictor plate. See Restricting Vents.Main burner flame isa blue, lazy, transparentflame.White / grey film forms.Pilot burning. Pilotindicator light is notflashing.Blockage in vent.Incorrect installation (verticaltermination only).Sulphur from fuel is being depositedon glass, logs or combustionchamber surfaces.Batteries exhausted.- remove blockage. In really cold conditions, ice buildup mayoccur on the terminal and should be removed as required.- refer to Figure 24 to ensure correct location of storm collars.- clean the glass with a recommended gas fireplace glasscleaner. DO NOT CLEAN GLASS WHEN HOT.If deposits are not cleaned off regularly, the glass may becomepermanently marked.- change batteries.W415-0496 / B / 08.10.05
Page 2 and 3: 2WARNINGS & SAFETY PRECAUTIONSWHAT
Page 4 and 5: 4NAPOLEON products are manufactured
Page 6 and 7: 6Provide adequate accessibility cle
Page 8 and 9: 8AIR TERMINAL INSTALLATIONSFIGURE 8
Page 10 and 11: 10TYPICAL VENT INSTALLATIONSNOTE:Wh
Page 12 and 13: 12HORIZONTAL TERMINATIONwhen (H T)
Page 14 and 15: 14when (H T) > (V T)Simple venting
Page 16 and 17: 16HORIZONTAL VENTING INSTALLATIONFO
Page 18 and 19: 18FINISHINGGLASS DOOR INSTALLATIONA
Page 20 and 21: 20OPERATION / MAINTENANCEPurge all
Page 22 and 23: 22Contact your dealer for questions
Page 26 and 27: 26Wolf Steel Fireplace Service Hist
Page 28: 28NOTESW415-0496 / B / 08.10.05

User Manual - ALLSEASONS Heating And Cooling

Create successful ePaper yourself

Delete template?

Save as template?