Product Guide - A. Stucki Company

More documents

Recommendations

Info

Side BearingsResilient Element: Resilient elementsshould be checked for cracks, gouges,or heat damage. Some elements (RB-17,RB-46, RB-56, RB-57, RB-58, RB-59, CSBcolumn) are composed of a single material,while others consist of two materials. Ingeneral, most dual material block designswill exhibit slight separation at the horizontalinterface of those two materials afterseveral months in normal service. Blocksshowing superficial horizontal separationdo not need replaced. As a rule, if theinterface can be manually opened to reveal50% or more of the interface surface, theblock should be replaced. Vertical cracksare acceptable unless there are more thantwo cracks, greater than 1/2” in lengthlocated in the lower, springing portionof the block. Cracks located below thewedge shaped metal cap do not affect itsperformance.www.stucki.com45
Free Height Measurement: The suitabilityof resilient blocks for continued servicecan be determined by their free heightmeasurement. Allow the blocks to relaxat least one hour at room temperatureafter the removal of the car body. Thenmeasure the height from the base to thehighest point on the block (see table 2.1).Side Side Bearings BearingsTable 2.1www.stucki.com46
Page 1: ProductGuideRev. 06 12/06
Page 4 and 5: Table of Contents4. Hydraulic Stabi
Page 6 and 7: 1. ScopeThis pocket guide provides
Page 8: Side BearingsFig. 2.1 — Shear Sid
Page 14: Side BearingsFig. 2.7 — RetroXT S
Page 25 and 26: Side Side Bearings BearingsFig. 2.1
Page 33 and 34: End Closure: End closures must be i
Page 36: Side BearingsShop SET UP5-1/8" ± 1
Page 40 and 41: Side BearingsYard Inspection: Verti
Page 42 and 43: Side BearingsShop SET UP3/4" ± 1/1
Page 44 and 45: Side BearingsShop InspectionGeneral
Page 48 and 49: Side BearingsLoad Cell Testing: A s
Page 50 and 51: Side BearingsThese measurements ass
Page 52 and 53: Side BearingsFig. 2.32 — Vertical
Page 54 and 55: Side BearingsFig. 2.34 — Setup He
Page 56 and 57: Side BearingsTo increase the setup
Page 58 and 59: Table 3.1Friction Elements*Requires
Page 60 and 61: Friction ElementsFig. 3.3 — RFE-5
Page 62 and 63: Friction ElementsFig. 3.7 — Wear
Page 64 and 65: Friction ElementsThe upper corners
Page 66 and 67: Friction ElementsIf wedge rise meas
Page 68 and 69: 4. Hydraulic StabilizersStucki hydr
Page 70 and 71: Yard and Shop InspectionHydraulic S
Page 72 and 73: Condition A. The oil level in the r
Page 74 and 75: HS-7 and HS-7100 units removed onac
Page 76 and 77: International ProductsAustralia, Ne
Page 78 and 79: International ProductsFig. 5.3 —
Page 80 and 81: International Products675-RXL Side
Page 82 and 83: International Products656-CRL Side
Page 84 and 85: International ProductsThe JOEY Seri
Page 86 and 87: International ProductsSeveral sligh
Page 88 and 89: International ProductsSA-5000-2R Si
Page 90 and 91: International ProductsAustralia and
Page 92 and 93: International ProductsRFE-3262 Resi
Page 94 and 95: 6. Brake BeamsBrake BeamsFig. 6.1
Page 96 and 97:
Brake BeamsInspectionReplacement of
Page 98 and 99:
PinRetainerBrake BeamsStrutLeverSlo
Page 100 and 101:
Reconditioning Services7. Reconditi
Page 102 and 103:
Reconditioning ServicesFig. 7.1 —
Page 104 and 105:
Reconditioning ServicesFriction Com
Page 106 and 107:
Reconditioning ServicesGears which
Page 108 and 109:
Reconditioning ServicesNew parts in
Page 110 and 111:
Product Index (continued)Product In
Page 114 and 115:
Reconditioning ServicesImproving Ri
Page 116 and 117:
Table of Contents4. Hydraulic Stabi
Page 118 and 119:
1. ScopeThis pocket guide provides
Page 120 and 121:
Side BearingsFig. 2.1 — Shear Sid
Page 122 and 123:
Side BearingsFig. 2.3 — Compact C
Page 124 and 125:
Side BearingsFig. 2.5 — RetroXT L
Page 126 and 127:
Side BearingsFig. 2.7 — RetroXT S
Page 128 and 129:
Side BearingsFig. 2.9 — RetroXT 5
Page 130 and 131:
Side BearingsFig. 2.11 — 656-CR,
Page 132 and 133:
Side BearingsFig. 2.13 — 690-RL,
Page 134 and 135:
Side BearingsFig. 2.15 — 675-RL,
Page 136 and 137:
Side BearingsFig. 2.17 — ISB-9DR,
Page 138 and 139:
Side BearingsFig. 2.19 — ISB-10,
Page 140 and 141:
Side BearingsFig. 2.21 — 656-SLB,
Page 142 and 143:
Side BearingsFig. 2.23 — 688-BNot
Page 144 and 145:
Side BearingsYard InspectionGeneral
Page 146 and 147:
Side BearingsRocker: Rockers may no
Page 148 and 149:
Side BearingsShop SET UP5-1/8" ± 1
Page 150 and 151:
Side BearingsIf reasonably level tr
Page 152 and 153:
Side BearingsYard Inspection: Verti
Page 154 and 155:
Side BearingsShop SET UP3/4" ± 1/1
Page 156 and 157:
Side BearingsShop InspectionGeneral
Page 158 and 159:
Side BearingsResilient Element: Res
Page 160 and 161:
Side BearingsLoad Cell Testing: A s
Page 162 and 163:
Side BearingsThese measurements ass
Page 164 and 165:
Side BearingsFig. 2.32 — Vertical
Page 166 and 167:
Side BearingsFig. 2.34 — Setup He
Page 168 and 169:
Side BearingsTo increase the setup
Page 170 and 171:
Table 3.1Friction Elements*Requires
Page 172 and 173:
Friction ElementsFig. 3.3 — RFE-5
Page 174 and 175:
Friction ElementsFig. 3.7 — Wear
Page 176 and 177:
Friction ElementsThe upper corners
Page 178 and 179:
Friction ElementsIf wedge rise meas
Page 180 and 181:
4. Hydraulic StabilizersStucki hydr
Page 182 and 183:
Yard and Shop InspectionHydraulic S
Page 184 and 185:
Condition A. The oil level in the r
Page 186 and 187:
HS-7 and HS-7100 units removed onac
Page 188 and 189:
International ProductsAustralia, Ne
Page 190 and 191:
International ProductsFig. 5.3 —
Page 192 and 193:
International Products675-RXL Side
Page 194 and 195:
International Products656-CRL Side
Page 196 and 197:
International ProductsThe JOEY Seri
Page 198 and 199:
International ProductsSeveral sligh
Page 200 and 201:
International ProductsSA-5000-2R Si
Page 202 and 203:
International ProductsAustralia and
Page 204 and 205:
International ProductsRFE-3262 Resi
Page 206 and 207:
6. Brake BeamsBrake BeamsFig. 6.1
Page 208 and 209:
Brake BeamsInspectionReplacement of
Page 210 and 211:
PinRetainerBrake BeamsStrutLeverSlo
Page 212 and 213:
Reconditioning Services7. Reconditi
Page 214 and 215:
Reconditioning ServicesFig. 7.1 —
Page 216 and 217:
Reconditioning ServicesFriction Com
Page 218 and 219:
Reconditioning ServicesGears which
Page 220 and 221:
Reconditioning ServicesNew parts in
Page 222 and 223:
Product Index (continued)Product In
Page 226:
Reconditioning ServicesImproving Ri
show all

Product Guide - A. Stucki Company

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?