CGâ3/3M AUTOGRAV - Scintrex

More documents

Recommendations

Info

Getting StartedPOWERING UP THE <strong>AUTOGRAV</strong>1. Set the charger to the appropriate line voltage (115V or 230V) by adjustingthe voltage setting switch on the charger.2. Check the charger fuse by unscrewing the fuse holder. Each voltagesetting requires a different fuse rating.Fuses are available in the Spare Parts Kit.Voltage Fuse115V 0.75A230V 0.375A3. After you have set the charger voltage and checked the fuse, plug thepower cord of the charger into an AC outlet. The green light on thecharger turns on to indicate that the charger is working.Figure 3Front View of the Autograv with Charger2-4 Autograv CG–3 Manual
Powering up the Autograv4. Remove the dust cap from the charger plug on the Autograv.5. While holding the top of the instrument, insert the charger connectorto the charger plug on the Autograv.6. Open the battery compartment by pressing down on the two latchesand lifting the cover away from the instrument.7. Remove the battery by pushing on the left side of the battery and thenpulling the black tab towards you so the battery can slide out of thecompartment.8. Insert the connector of the battery into either socket on the left side ofthe compartment. The Autograv has two sockets so that you can changebatteries without powering down the instrument (see Figure 4).9. Before you reinstall the battery, place your hand inside and flatten theblack tab against the bottom, side and top of the compartment. If theblack tab is not pressed against the walls of the compartment, thebattery will not fit and the foam padding will be damaged.How To10.Place the battery inside of the compartment with the top of the batteryfacing outwards and the battery cable to the left as shown in Figure 4.11.Reinstall the battery compartment cover.Autograv CG–3 Manual 2-5
Page 1 and 2: CG-3/3M AUTOGRAVAUTOMATED GRAVITY M
Page 3 and 4: Autograv CG-3Table of ContentsSecti
Page 5 and 6: Section 5: BATTERY AND CHARGERLoss
Page 7 and 8: Appendix C: INTERFACING WITH THE AU
Page 9 and 10: Autograv CG-3Section1INSTRUMENT OVE
Page 11 and 12: Autograv CG-3 Manual 1-3Introductio
Page 13 and 14: Autograv CG-3Section2GETTING STARTE
Page 15: Starting up the AutogravSTARTING UP
Page 19 and 20: Using the KeypadUSING THE KEYPADFig
Page 21 and 22: Using the KeypadKey506AUXDescriptio
Page 23 and 24: The DisplayTHE DISPLAYPARAMETER SET
Page 25 and 26: The DisplayModifying ParametersThe
Page 27 and 28: The DisplayHow ToAutograv CG-3 Manu
Page 29 and 30: The DisplayFigure 6Autograv Softwar
Page 31 and 32: Initializing the Instrument Paramet
Page 41 and 42: The Display during ReadingsPress th
Page 43 and 44: Setting up the TripodTo set up1. Se
Page 45 and 46: Setting up the Tripod7. Adjust the
Page 47 and 48: Temperature CompensationTEMPERATURE
Page 49 and 50: Temperature CompensationHow ToAutog
Page 51 and 52: Temperature CompensationTo AdjustAd
Page 53 and 54: Adjusting Drift CorrectionsADJUSTIN
Page 55 and 56: Adjusting Drift CorrectionsR2,T20.
Page 57 and 58: Adjusting Drift Corrections503. Pre
Page 59 and 60: Recalling DataRECALLING DATA▲▲
Page 61 and 62: Recalling Data▲If the DATA or INF
Page 63 and 64: Recalling DataRECALLING DATA IN THE
Page 65 and 66: Autograv CG-3Section3INSTRUMENT PAR
Page 67 and 68:
INITIALISE MenuINITIALISE MENUeTher
Page 69 and 70:
INITIALISE MenuThe 48K represents t
Page 71 and 72:
INITIALISE MenuExample: If you sele
Page 73 and 74:
INITIALISE Menuee3. Press the CHANG
Page 75 and 76:
INITIALISE MenuNotes:If you select
Page 77 and 78:
INITIALISE Menu13. TIME HH:MM:SSYou
Page 79 and 80:
STN SEPSTN SEPThere are no submenus
Page 81 and 82:
AUTOGRAV SETUP1. MODEYou can select
Page 83 and 84:
AUTOGRAV SETUPe 6e9. Press the ENTE
Page 85 and 86:
AUTOGRAV SETUP4. CAL. AFTERYou can
Page 87 and 88:
AUTOGRAV SETUPTIDE CORRECTIONCHG? >
Page 89 and 90:
AUTOGRAV SETUPe4. Key in the value.
Page 91 and 92:
AUTOGRAV SETUPeee4. Press the CHANG
Page 93 and 94:
AUTOGRAV SETUP11. INITIAL CONSTANTS
Page 95 and 96:
OUTPUTNotes: ▲ To dump data which
Page 97 and 98:
OUTPUTTRACE1: > NNNNSELECT/ENTERYou
Page 99 and 100:
OUTPUTea. Select the multiplier or
Page 101 and 102:
OUTPUTg) START PLOT13. Press the 0
Page 103 and 104:
OUTPUT7. CR DELAYYou can set the ca
Page 105 and 106:
LOCK AUX.LOCK AUX.The LOCK AUX mode
Page 107 and 108:
Autograv CG-3Section4FIELD OPERATIO
Page 109 and 110:
Parameter Setup and Keypad Operatio
Page 111 and 112:
Recording DataThe auto-rejection fe
Page 113 and 114:
Operation Hints▲▲▲Ensure that
Page 115 and 116:
Operation Hintsis reduced by signal
Page 117 and 118:
Dumping Data1. After the instrument
Page 119 and 120:
Autograv CG-3Section5BATTERY AND CH
Page 121 and 122:
Batterypower to the instrument. Onc
Page 123 and 124:
ChargerREPLACINGYou should replace
Page 125 and 126:
Charger3. Change the charger fuse t
Page 127 and 128:
How to Change a Battery3. Insert th
Page 129 and 130:
Autograv CG-3Section6MAINTENANCEThe
Page 131 and 132:
Drift Correction▲▲tion feature
Page 133 and 134:
Tilt Correction Adjustment2. Place
Page 135 and 136:
Tilt Correction AdjustmentMaintenan
Page 137 and 138:
Tilt Correction AdjustmentFine Adju
Page 139 and 140:
Tilt Correction AdjustmentCoarse Ad
Page 141 and 142:
Tilt Correction AdjustmentAdjusting
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Recalibrating the GravimeterA linea
Page 149 and 150:
Autograv CG-3Section7TROUBLESHOOTIN
Page 151 and 152:
Autograv CG-3Section8REFERENCE INFO
Page 153 and 154:
Standard AccessoriesSTANDARD ACCESS
Page 155 and 156:
Instrument Parts ListINSTRUMENT PAR
Page 157 and 158:
Warranty and RepairWARRANTY AND REP
Page 159 and 160:
Autograv CG-3AppendixATHEORY OF OPE
Page 161 and 162:
Introductionever, since there is no
Page 163 and 164:
IntroductionCONTROL CONSOLE AND SOF
Page 165 and 166:
Spring Service Life and Reading Ran
Page 167 and 168:
Spring Service Life and Reading Ran
Page 169 and 170:
Processing of the Gravity SignalCor
Page 171 and 172:
Compensation and CorrectionsRU( t 2
Page 173 and 174:
Compensation and CorrectionsIf the
Page 175 and 176:
Compensation and CorrectionsGRAVITY
Page 177 and 178:
Autograv CG-3AppendixBELASTIC HYSTE
Page 179 and 180:
Figure B-1 Elastic Hysteresis Effec
Page 181 and 182:
Autograv CG-3AppendixCINTERFACING W
Page 183 and 184:
IGS OutputDCE to DTEFunction Pin Pi
Page 185 and 186:
IGS OutputMaleNORMAL5 5 Clear to Se
Page 187 and 188:
Autograv CG-3AppendixDINITIAL CONST
Page 189 and 190:
Autograv CG-3IndexIndexAAccessories
Page 191 and 192:
FNotebook feature 4-5Output 2-37Rec
Page 193 and 194:
MKKey functions 2-6, 2-7Enter mode
Page 195 and 196:
RData 2-37DATA BITS 3-37DUMP ALL DA
Page 197 and 198:
WTEC A-15EffectsBatteries 5-2Termin
show all

CGâ3/3M AUTOGRAV - Scintrex

Create successful ePaper yourself

Delete template?

Save as template?

CGâ3/3M AUTOGRAV - Scintrex