technical data sheet ULTRAFINE FINISH - Bostik Hong Kong Limited

PLACINGBostik Ultrafine Finish is easily applied to any preparedsurface using a steel trowel. Apply sufficient pressure tofill all defects and feather the product into the adjacentsubfloor surface. It is not necessary to leave a minimumthickness of product on the substrate. Use the leaseamount possible to attain the desired smoothness.Ultrafine Finish can be applied from feather edge to up to5mm. Subsequent floor coverings can be installed assoon as it has thoroughly hardened (45 mins @ 23 o C –50%RH).Thickness of Installation: Ultrafine Finish can beinstalled from a true feather edge up to 6mm thick overlarge areas in one application.CURINGApproximately 15 minutes at 20 o C. Note: The pot life willvary with ambient temperature and conditions. Mix onlythe amount of Ultrafine Finish that will be usedimmediately to avoid waste. Accepts floor coverings in45 minutes.CLEAN-UPUltrafine Finish should be removed from tools andequipment with clean water immediately after use.PACKAGINGUltrafine Finish is supplied in a 5kg pail.COVERAGE16-18m 2 per 5kg pail over concrete, depending onapplication thickness.30-35m 2 per 5kg pail over plywood, or very smooth densesurfaces depending on application thickness. A 5kg pailwhen mixed with 2.5 litres of water will yield approx. 4.5litres.STORAGEUltrafine Finish has a shelf life of approximately 12months if kept in original sealed plastic pail in a dryenvironment away from moisture. For further informationconsult Bostik TECHNICAL DATA SHEET.PRECAUTION• Do not over water.• Large quantities should not be hand mixed.• Can be walked on after 45 minutes.• Most floor coverings can be laid after 45 minutes.• Check moisture content in large / thick applicationsprior to laying floor coverings.• Protect from direct sunlight or drying winds duringcure.• Do not use in areas subject to hydrostatic head ofpressure, refer Bostik Moisture Seal treatment.• Do not use in areas subject to constant contact withmoisture, refer Bostik Moisture Seal treatment.• Not recommended as a finished floor coating orwearing surface.HEALTH AND SAFETYHAZARDOUSCement products are classified as hazardous underGeneral Heath and Safety guidelines and materialscontaining Portland cement are alkaline in nature.RISKHarmful: danger of serious damage to health byprolonged exposure through inhalation.SAFETY DIRECTIONSAvoid contact with skin and eyes. Avoid breathing dust.Wear overalls, safety shoes, impervious gloves andchemical goggles. Use only in well ventilated areas. Ifinhalation risk exists wear dust respirator. Avoid contactwith foodstuffs. Wash hands thoroughly after use. Storein a cool place and out of direct sunlight. Keep containersclosed when not in use. Do not empty into drains.FIRENon-combustible, however, if involved in a fire use waterfog, foam or dry agents. Avoid breathing products ofcombustion.SPILLSClear area of all unprotected personnel. Slippery whenspilt. Wear protective equipment. Collect and seal inproperly labelled drums.FIRST AIDIf poisoning occurs, contact a Doctor.SWALLOWEDIf swallowed, do NOT induce vomiting. Give a glass ofwater. Seek medical assistance.EYEIf in eyes, hold eyes open, flood with water for at least 15minutes and see a doctor.SKINIf skin contact occurs, remove contaminated clothing andwash skin thoroughly. If irritation occurs seek medicaladvice.INHALED: Remove from contaminated area. Seekmedical advice.DO NOT REUSE CONTAINER UNLESSTHOROUGHLY DECONTAMINATED.SEE THE MATERIAL SAFETY DATA SHEET FORADDITIONAL INFORMATION.ULTRAFINE FINISH PAGE 2 of 3.