Uncontrolled

More documents

Recommendations

Info

Use the spigot wrench 282 660. Rear shell view 1 Slide the cable clamp onto the cables fitted with insert module. Be careful : the backshe/1 can only be mounted one way round, so ensure that cables are located in correct cavity A or B. 2 Install the insert module into the connector shell. 3 Apply some thread lock onto the assessory thread of the connector shell. 4 Mount the cable clamp onto the rear of the connector. 5 Screw and tighten the locking screw with the spigot wrench. Ensure that the cable clamp is correctly engaged in the shell. 6 Anchor the cable with Ty-Rap® using the slot of the cable clamp. Use a spanner with 5,5 mm across flats. • For all backshells and cable clamps. 1 Remove the nuts of two polarizing keys. 2 Remove the polarizing keys. 3 For the backshell : Thread cables through the outlet of the backshell. 4 Fit the contacts into the insert module. 5 Install the insert module into the connector shell. 6 Mount the backshell or the cable clamp onto the rear of the connector. 7 Replace the polarizing keys in their new position (page 22). 8 Replace the washers and screws and tighten them with the spanner. 9 For cable clamp 617 921 005/006 : Fit the four screws (supplied with cable clamp) in the four threaded holes. • Cabling the outlet : Backshells 617 905 and 617 907 : Insert the cables through the outlet and fix them with a Ty-Rap®. Backs hells 617 906 and 617 908 : Follow mounting operations of 10 to 14 for backs hell 617 902 page 60. Cable clamp 617 921 001/002/003/004 : Lay cables against suitable slot (depending on cable size) and fix with a Ty-Rap®. <strong>Uncontrolled</strong> Copy Slot forTy-Rap Backs hell ' cr:l}--Nut Shell Polarizing key ® Trade Mark of Thomas & Betts Corp RADIALL ® The Qualit y Connectio n -62-
Use the spigot wrench 282 660. Rear shell view 1 Introduce the spigot wrench into the two slots of the cyl!ndrical nut. 2 Loosen the nut and remove it completely. 3 Pull out the polarizing key of the shell to change the polarizing code. 4 Replace the polarizing key in a new position (page 34 - 35). 5 Replace and tighten the cylindrical nut with the spigot wrench. Shell Polarizing key ~ Use the spigot wrench 282 660. 1 Introduce the spigot wrench into the two slots of the cylindrical nut. 2 Loosen the nut and remove it completely. 3 Pull out the polarizing key of the shell to change the polarizing code. 4 replace the polarizing key in a new position (page 34 - 35) . 5 Replace and tighten the cylindrical nut with the spigot wrench. Front shell view <strong>Uncontrolled</strong> Copy Spigot wrench ~olarizing key Hexagon cavity ---4.!:or'rr---,,f J RADIALL ® The Qua lity Connection -63-
Page 1 and 2:
Uncontrolled Copy Supplied by: Dist
Page 3 and 4:
Multicontact connectors EPX series
Page 5 and 6:
Multicontact connectors EPX series
Page 7 and 8:
EPX 2 P 17 * .. REFERENCE 617 900 .
Page 9 and 10:
E 40 P Y ·············
Page 11 and 12: The modular construction of the EPX
Page 13 and 14: PIN INSERT MODULES : MATING FACE Te
Page 15 and 16: 0 0 0 0 [_______) 617 921 003/004 E
Page 17 and 18: 18. 30 ±0. 10 (. 720± .004) M 3 x
Page 19 and 20: 50. 10 (.ZOO) MAX * Polarization an
Page 21 and 22: 4 HOLES M 2 x 0,40 C'SUNK 90' ENVIR
Page 23 and 24: 13 (. 512) ON FLATS 50 MAX ( 1. 969
Page 25 and 26: FIXED MOUNTING ON FRONT OF PANEL (e
Page 27 and 28: I EPX 2 B 14 * I EPX 2 R 18 * 'L..-
Page 29 and 30: 18,30 ±0, 10 ( . 7 20 ± . 004) 5.
Page 31 and 32: Cable version 15 60 + 0· 20 . -0 .
Page 33 and 34: 15 . 60 ~~ : ~~ ( . 6 14 ~ : ~~~) ~
Page 35 and 36: Polarization code is marked on the
Page 37 and 38: 46 MAX ( 1.811) 26.50 ( 1.043) 1' 3
Page 39 and 40: FIXED MOUNTING ON FRONT OF PANEL (e
Page 41 and 42: Filtered EPX connectors provide a c
Page 43 and 44: 22 reduced crimp barrel 28 30 Pin 6
Page 45 and 46: 22 socket 617 303 II 1 ip 0, 60x0,
Page 47 and 48: 15 RG178 KX21 s. T. Pin 617131 Sock
Page 49 and 50: CRIMP TOOLS M22520/1-01 M22520/2-01
Page 51 and 52: Cables: RG58, RG141, RG142, RG223,
Page 53 and 54: Semi-rigid cables: .085, .047 For c
Page 55 and 56: Semi-rigid cable : .047 For center
Page 57 and 58: The insert module is assembled into
Page 59 and 60: Use the spigot wrench 282 661. Rear
Page 61: Use the spigot wrench 282 661. Rear
Page 65 and 66: RADIALL can manufacture various she
Page 67: Multicontact connectors EPX series
show all

Uncontrolled

Create successful ePaper yourself

Delete template?

Save as template?