Planetary Gear Drive

More documents

Recommendations

Info

■ E Technical Data ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ■Lubrication 1. Standard Lubrication Method ・Oil bath lubrication is applied to all models. ・Grease lubrication for some right angle input shaft. 2. Recommended Lubricants <strong>Gear</strong> Oil Ambient Temperature -10 deg to +25 deg +10 deg to +40 deg +30 deg to +50 deg ISO AGMA VG150 4EP VG220 5EP VG320 6EP Bearing grease BP CASTROL CHEVRON TEXACO EXXON MOBIL SHELL TOTAL ENERGOL GR-XP-150 ENERGOL GR-XP-220 ENERGOL GR-XP-320 ENER-GREASE LS EP2 ALPHA SP150 ALPHA SP220 ALPHA SP320 SPHEEROL AP3 OPTIGEAR BM150 OPTIGEAR BM220 OPTIGEAR BM320 Olista Longtime 3EP TRIBOL 1100/150 TRIBOL 1100/220 TRIBOL 1100/320 TRIBOL 3020/1000-2 GEAR COMPOUNDS EP150 GEAR COMPOUNDS EP220 GEAR COMPOUNDS EP320 DURALITH GREASE 68 MEROPA WM150 MEROPA WM220 MEROPA WM320 MULTI- FAK EP2 SPARTAN EP150 SPARTAN EP220 SPARTAN EP320 BEACON EP2 MOBIL GEAR 600XP150 MOBIL GEAR 600XP220 MOBIL GEAR 600XP320 MOBIL- PLEX 48 OMALA 150 OMALA 220 OMALA 320 ALVANIA EP2 CARTER EP150 CARTER EP220 CARTER EP320 MULTIS EP2 ・Because the lubrication part of grease fills grease when shipping it, it is used as it is and is excellent. 3. Time of replenishment and replacement. ・Lubricant has been evacuated on shipment. Be sure to replenish lubricant up to the standard level of oil gauge. It is recommended to replace lubricant after 500 hours operation for the first time and in every 2500 hours or every half year, whichever comes first, after then. 4. Consult us when the ambient temperature is lower than -10℃ or higher than +40℃, when the standard input speed will be over 1800r/min or when irregular operating condition will be required. ■Installation (1) Consult us when the product is to be installed on an inclined surface or on a ceiling. Additional lubrication system may be necessary. (2) Install the product horizontally on a sufficiently rigid base. When the product is made for inclined installation according to your specification, do not install it at any other angle than the specified angle. (3) Installation bolts for the reducer shall be equivalent to JIS(ISO) strength classification 10.9. Consult us when the force that pushes up reducer is to be applied. (4) Refer to the maintenance manual attached to the product for other remarks regarding to installation and maintenance. E-2
E Technical Data ■ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ■Painting Specifications Surface Condition Cast Iron Class 1 Steel Plate Class 2 Kind of Painting Painting Specification Class Painting of Days Coating Type Finish Coat (Thickness:µm) Type of Coating Standard painting 1 - Under Modified alkyd resin (20~40) 0 1 Phallic acid Finish Alkyd resin paint (15~30) 2 - Under Modified alkyd resin Standard export (40~80) 2 panting 1 Modified epoxy Finish Vinyl modified epoxy resin (15~30) Modified epoxy 3 Under 1 (20~40) Vinyl modified epoxy resin Finish 2 (30~60) Vinyl modified epoxy resin 2 Under Lead rust preventive paint Long of oil (40~70) 7 phallic 2 Finish Synthetics resin paint Special painting (30~60) (Including rust- 2 Under proof and heat (40~70) Lead rust preventive paint resisting painting) 1 Chloride rubber 10 Second One layer of (20~40) Phenol M.I.O. paint Modified alkyd 2 Finish resin Primer as the (40~70) Chloride rubber paint first prime 2 Under Lead rust preventive paint (40~70) Phenol 7 2 Finish Phenol resin enamel (30~60) Heat-proof silver 7 Under 1 (20~40) Lead rust preventive paint Finish 1 (15~30) Aluminum paint 1 Special permeability epoxy Under (50~60) aluminum paint Epoxy 10 3 Finish Polyamide epoxy Extra rust-proof (120~240) painting 1 Special permeability epoxy Under (50~60) aluminum paint Polyurethane 10 3 Polyisocyanate urethane Finish (45~90) resin paint Extra rust-proof painting(Sand blast under coating) Thick film epoxy 12 5 (250~350) Thick film type modified epoxy resin paint Note: 1. Days mean extra days necessary for Special Painting in comparison with Standard Painting. 2. Our standard color is Munsell 2.5G 6/3. ■Rust Proof Standard Application Standard under coat Standard finish coat Export standard Moderate corrosive atmosphere, seaside, outdoor humid atmosphere, etc. Ocean-going vessels, bridge, seaside, outdoor humid atmosphere, etc. Ocean-going vessels, bridge, seaside, outdoor humid atmosphere, etc. In-and-outdoor of acid treating plant and chemical plant, etc. Heating furnace(120℃), etc. Nuclear power generation Nuclear power generation Submersible equipment, marine structure, etc. Rust proofing treatment has been conducted on all completely assembled models prior to shipment. 1. Standard rust proofing specifications (1) Outside rust proofing specifications Rust proofing oil has been applied to products before shipment. Check the rust proofing conditions every 6 months after shipment, and conduct rust proofing treatment, if necessary. (2) Inside rust proofing specifications Rust proofing period 6 months Generally to be stored inside the warehouse, relatively free of humidity, dust, extreme temperature Storage condition fluctuation, corrosive gas, and similar atmosphere. After shipment, the product shall be operated 5-10 minutes every 2-3 months with our recommended lubricants. 2. Export rust proofing specifications Consult us for export rust proofing when export specifications or severe specifications are required. E―3
Page 3:
® Planetary Gear Drive DP1000 Seri
Page 6 and 7:
A-2
Page 8 and 9:
■ A Features ● ● ● ● ●
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
■ B Reducer ● ● ● ● ●
Page 18 and 19:
■ B Reducer ● ● ● ● ●
Page 20 and 21:
■ B Reducer ● ● ● ● ●
Page 22 and 23:
■ B Reducer ● ● ● ● ●
Page 24 and 25:
■ B Reducer ● ● ● ● ●
Page 26 and 27:
■ B Reducer ● ● ● ● ●
Page 28 and 29:
■ B Reducer ● ● ● ● ●
Page 30 and 31:
■ B Reducer ● ● ● ● ●
Page 32 and 33:
■ B Reducer ● ● ● ● ●
Page 34 and 35:
■ B Reducer ● ● ● ● ●
Page 36 and 37:
■ B Reducer ● ● ● ● ●
Page 38 and 39:
■ B Reducer ● ● ● ● ●
Page 40 and 41:
■ B Reducer ● ● ● ● ●
Page 42 and 43:
■ B Reducer ● ● ● ● ●
Page 44 and 45:
■ B Reducer ● ● ● ● ●
Page 46 and 47:
■ B Reducer ● ● ● ● ●
Page 48 and 49:
■ B Reducer ● ● ● ● ●
Page 50 and 51:
■ B Reducer ● ● ● ● ●
Page 52 and 53:
■ B Reducer ● ● ● ● ●
Page 54 and 55:
■ B Reducer ● ● ● ● ●
Page 56 and 57:
■ B Reducer ● ● ● ● ●
Page 58 and 59:
■ C Drive Unit ● ● ● ●
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83: ■ C Drive Unit ● ● ● ●
Page 120 and 121: ■ D Applications ● ● ● ●
Page 134 and 135: ■ E Technical Data ● ● ●
Page 144: ■ E Technical Data ● ● ●
show all

Planetary Gear Drive

Create successful ePaper yourself

Delete template?

Save as template?