Planetary Gear Drive

More documents

Recommendations

Info

■ E Technical Data ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ■Specifications/Dimensions for Spline Shaft In case spline shaft is used for slow speed shaft, dimensions are as follows. 2-S×L2 φDE W LE φD(max) L (Unit:mm) Size Spline spec. φD(max) φDE L LE W S L2 1100 120×22×5 119 - 100 100 63 M16 32 1110 130×24×5 129 - 110 110 80 M20 45 1120 150×18×7.5 148.5 - 120 120 80 M20 45 1130 160×19×7.5 158.5 - 130 130 100 M24 51 1140 180×22×7.5 178.5 - 150 150 100 M24 51 1150 200×25×7.5 198.5 200p6 220 160 125 M30 64 1160 220×20×10 218 220p6 250 170 125 M30 64 1170 240×22×10 238 240p6 260 180 125 M30 64 1180 260×24×10 258 260p6 260 180 160 M36 70 1190 280×26×10 278 280p6 300 220 160 M36 70 1200 320×30×10 318 320r6 320 240 200 M36 70 1210 360×34×10 358 360r6 330 250 200 M36 70 1220 400×38×10 398 400r6 340 260 250 M36 70 <strong>Gear</strong> standard:In conformity with JIS B1603-1995 attachment “Involute Spline (standard pressure angle 20°)”. (Same as old standard JIS D2001-1959”Involute Spline for automobiles”.) E-6
E Technical Data ■ ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● ■Dimensions of Motor Adapter JEM / IEC Motor Capcity code JEM (Standard) Frame kW×pole size IEC kW×pole Frame size Unit : mm A LB C D E φMS H I LA LN LZ 02 0.2×4P 63 - 63 160 110 23 13 4.5 11 - - 130 4 10 05 0.4×4P 71 0.25×4P,0.37×4P 71 160 110 30 13 4.5 14 16.3 5 130 4 10 1 0.75×4P 80 0.55×4P,0.75×4P 80 200 130 40 13 4.5 19 21.8 6 165 4 12 2 1.5×4P 90L 1.1×4P,1.5×4P,1.85×4P 90L 200 130 50 13 4.5 24 27.3 8 165 4 12 3 2.2×4P 100L 2.2×4P,3×4P 100L 250 180 60 13 5 28 31.3 8 215 4 15 5 3.7×4P 112M 4×4P 112M 250 180 60 13 5 28 31.3 8 215 4 15 8 5.5×4P 132S 5.5×4P 132S 300 230 80 15 5 38 41.3 10 265 4 15 10 7.5×4P 132M 7.5×4P 132M 300 230 80 15 5 38 41.3 10 265 4 15 15 11×4P 160M 11×4P 160M 350 250 110 18 6 42 45.3 12 300 4 19 20 15×4P 160L 15×4P 160L 350 250 110 18 6 42 45.3 12 300 4 19 25 18.5×4P 180M - - 400 300 110 18 6 48 51.8 14 350 4 19 - - - 18.5×4P 180M* 350 250 110 18 6 42 45.3 12 300 4 19 30 22×4P 180M - - 400 300 110 18 6 48 51.8 14 350 4 19 - - - 22×4P 180L* 350 250 110 18 6 42 45.3 12 300 4 19 40 30×4P 180L 30×4P 200L 400 300 110 18 6 55 59.3 16 350 4 19 50,60 37×4P,45×4P 200L 37×4P, 45×4P 225S 450 350 140 22 6 60 64.4 18 400 8 19 75 55×4P 225S 55×4P 250M 550 450 140 22 6 65 69.4 18 500 8 19 Note 1. Motor adapters with other dimensions than as listed in this table can be also manufactured. Please send us your inquiry. Note 2. Special adapter may be necessary for these flanges with * mark. Please consult us when you need them. Note 3. As to these types of 37×4P, 45×4P, 55×4P, on which CYCLO Flange Motor is equipped (refer to C-22 & 23), flanges of JEM Standard will be specially applied. E―7
Page 3:
® Planetary Gear Drive DP1000 Seri
Page 6 and 7:
A-2
Page 8 and 9:
■ A Features ● ● ● ● ●
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
■ B Reducer ● ● ● ● ●
Page 18 and 19:
■ B Reducer ● ● ● ● ●
Page 20 and 21:
■ B Reducer ● ● ● ● ●
Page 22 and 23:
■ B Reducer ● ● ● ● ●
Page 24 and 25:
■ B Reducer ● ● ● ● ●
Page 26 and 27:
■ B Reducer ● ● ● ● ●
Page 28 and 29:
■ B Reducer ● ● ● ● ●
Page 30 and 31:
■ B Reducer ● ● ● ● ●
Page 32 and 33:
■ B Reducer ● ● ● ● ●
Page 34 and 35:
■ B Reducer ● ● ● ● ●
Page 36 and 37:
■ B Reducer ● ● ● ● ●
Page 38 and 39:
■ B Reducer ● ● ● ● ●
Page 40 and 41:
■ B Reducer ● ● ● ● ●
Page 42 and 43:
■ B Reducer ● ● ● ● ●
Page 44 and 45:
■ B Reducer ● ● ● ● ●
Page 46 and 47:
■ B Reducer ● ● ● ● ●
Page 48 and 49:
■ B Reducer ● ● ● ● ●
Page 50 and 51:
■ B Reducer ● ● ● ● ●
Page 52 and 53:
■ B Reducer ● ● ● ● ●
Page 54 and 55:
■ B Reducer ● ● ● ● ●
Page 56 and 57:
■ B Reducer ● ● ● ● ●
Page 58 and 59:
■ C Drive Unit ● ● ● ●
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87: ■ C Drive Unit ● ● ● ●
Page 120 and 121: ■ D Applications ● ● ● ●
Page 132 and 133: ■ E Technical Data ● ● ●
Page 144: ■ E Technical Data ● ● ●
show all

Planetary Gear Drive

Create successful ePaper yourself

Delete template?

Save as template?