HARDWARE

More documents

Recommendations

Info

WELD ON LIFTING POINT Bullivants BlueLink Weld On Lifting Point: Unit of Measure - Each Features: • Australian made • Forged D-ring and housing in Grade 100 material • Flat design • Test load and magnafl ux test loaded • Multi directional loading • Rated capacity can be increased 100% in specifi c lashing applications 05 - <strong>HARDWARE</strong> Working Load Limits (in tonnes) for symmetrical loading ORDER CODE Single Point WLL (tonne) 2, 3 or 4 Point Maximum Included Angle 60° 90° 120° 165451 2.0 3.4 2.8 2.0 164453 4.0 6.9 5.6 4.0 165452 6.7 11.6 9.5 6.7 WARNING - NEVER EXCEED THE WORKING LOAD LIMIT (WLL). 1300 722 999 www.bullivants.com MANUFACTURED IN AUSTRALIA USING ONLY HEAT CERTIFIED AUSTRALIAN STEEL. 125
05 - <strong>HARDWARE</strong> Rigging Screws & Turnbuckles Types of Turnbuckles and Rigging Screws Grade L Rigging Screws & Turnbuckles must comply with AS2319. In accordance with AS2319 turnbuckles and rigging screws should be marked with manufacturers identifi cation, nominal size, where the quality of the grade is other than L, the quality of grade shall be marked on the end fi tting., WLL in tonnes, identifi cation marking to correlate the rigging screw or turnbuckle to the test certifi cate. Commercial Grade Turnbuckles are not to be used for lifting purposes. Commercial Grade Turnbuckles are not made to any standard. Usually used for tensioning or supporting light loads. Care & Use • Ensure the WLL suits the application. • Markings can be clearly read. • The body and fitting of the rigging screw or turnbuckle is not distorted. • Conduct a visual inspection for nicks, gouges, cracks and corrosion. • Conduct a visual inspection for damaged screw threads. • Care should be taken to ensure that rigging screws and turnbuckles are not excessively tightened. Turnbuckles and rigging screws should be inspected periodically by a competent person as per AS2319 Rigging Screws Rigging Screws are used to provide a means for length adjustment and for tensioning. They are also used with guys for masts, towers and other structures and engineering applications. Rigging Screws generally have elongated eyes or clevis end fittings for connection to shackles, wire rope assemblies, pad eyes and the like. An observation hole is provided at the inner end of the thread, at each end of the body, which permits visual observation of the maximum permitted extended position of the end fi tting. Additionally, rigging screws have the innate facility for continuing lubrication as the enclosed section of the body provides a suitable reservoir for grease or other lubrication. Hence, they have an advantage in relative corrosive applications such as ship’s rigging and permanent outdoor guys. Rigging screws are not designed for continuous adjustment under rated load conditions. Turnbuckles Turnbuckles have the same applications as rigging screws, but generally have smaller size range and shorter adjustment. The main benefi t of a turnbuckle is that it may have a greater ability to be tightened under load. Also, there may be a wider scope for providing means for locking while in service. Turnbuckles are not designed for continuous adjustment under rated load. Grade L Rigging Screws Grade L Rigging Screw - Clevis & Clevis (Jaw & Jaw): Unit of Measure - Each ORDER CODE Size (mm) A (mm) Closed A (mm) Open C (mm) D (mm) E (mm) F (mm) K (mm) WLL (tonnes) Weight (kg) 160063 12 340 525 15 35 8.5 230 10 0.5 0.97 160068 16 360 535 20 40 9 230 12 0.75 1.36 160070 20 390 555 22 46 10.5 230 16 1.25 2.35 160075 24 555 740 30 58 13 360 20 2.5 4.2 Other sizes available. Grade L Rigging Screw - Eye & Eye: Unit of Measure - Each ORDER CODE Size (mm) A (mm) Closed A (mm) Open E (mm) F (mm) G (mm) H (mm) J (mm) WLL (tonnes) Weight (kg) 160046 16 350 525 9 230 17 36 12 0.75 1.09 160047 20 380 545 10.5 230 21 42 12 1.25 1.72 160072 24 540 725 13 360 25 51 17 2.5 3.2 Other sizes available. 126 1300 722 999
Page 1 and 2: OHS520211 FS520785 EMS520269 05 - H
Page 3 and 4: Grade S Tested Galvanised Screw Bow
Page 5 and 6: Galvanised Screw Bow Shackles: Unit
Page 7 and 8: Commercial Grade Shackles Galvanise
Page 9 and 10: Gunnebo ROV Shackle No. 860: Unit o
Page 11 and 12: RUD Starpoint Eyebolts - Grade 100
Page 13 and 14: RUD Weld-On Load Rings - Grade 100:
Page 15 and 16: RUD PP-B Bolt-On Swivelling: Unit o
Page 17 and 18: Gunnebo SLP Screw-on Lifting Points
Page 19: Black Metric Eyenuts: Unit of Measu
Page 23 and 24: Grade L Turnbuckles - Clevis (Jaw)
Page 25 and 26: Superbuckles - Eye & Eye: Unit of M
Page 27 and 28: Crosby G-416 Open Spelter Sockets:
Page 29 and 30: PWB Forged Closed Swage Wire Rope S
Page 31 and 32: Wire Rope Grips Wire Rope Grips AS2
Page 33 and 34: Ferrules Aluminium Ferrules DIN Gra
Page 35 and 36: NCG Cable Stockings Cable stockings
Page 37 and 38: Heavy Duty Graded Weave (Tubular):
Page 39 and 40: PWB Anchor Single Sheave Blocks - M
Page 41 and 42: Crosby 431 Snatch Blocks: Unit of M

HARDWARE

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?