DIMENSIONS

UP
Class 3 – AS 4041 Maximum operating pressures in MPa for UltraPipe
Fluid 1 Fluid 2 Fluid 3 Fluid 4
Design Strength MPa f 176 156 176 156 176 156 176 156
Thickness tolerance factor 0.925 0.925 0.925 0.925 0.925 0.925 0.925 0.925
Piping class factor M 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
Weld joint factor e 1 1 1 1 1 1 1 1
Maximum Operating Temperature
Ambient 100ºC Ambient 100ºC Ambient 100ºC Ambient 100ºC
OD WT MDMTºC
5.0
3.7
2.5
Class 2P – AS 4041 Maximum operating pressures in MPa for UltraPipe
Fluid 1 Fluid 2 Fluid 3 Fluid 4
Design Strength MPa f 176 156 176 156 176 208 208 156
Thickness tolerance factor 0.925 0.925 0.925 0.925 0.925 0.925 0.925 0.925
Piping class factor M 1 1 1 1 1 1 1 1
Weld joint factor e 1 1 1 1 1 1 1 1
OD WT MDMTºC
457.0
457.0
457.0
406.4
406.4
406.4
355.6
355.6
355.6
323.9
323.9
323.9
273.1
273.1
273.1
273.1
12.7
9.5
6.4
12.7
9.5
6.4
12.7
9.5
6.4
12.7
9.5
6.4
12.7
9.3
6.4
4.8
-20
-25
-40
-20
-25
-40
-20
-25
-40
-20
-25
-40
-20
-25
-40
-50
Maximum Operating Temperature
Ambient 99ºC Ambient 99ºC Ambient 99ºC Ambient 99ºC
This class is
not suitable for
fluid 1
This class is
not suitable for
fluid 2
This class is
not suitable for
fluid 3
11.0
8.2
5.5
12.5
9.2
6.2
14.3
10.6
7.1
15.7
11.7
7.8
18.8
13.6
9.3
6.9
8.3
6.2
4.1
9.3
6.9
4.6
10.7
8.0
5.3
11.8
8.8
5.8
14.1
10.2
7.0
5.2
219.1
219.1
219.1
219.1
168.3
168.3
168.3
114.3
114.3
88.9
88.9
8.2
6.4
4.8
4.0
5.6
4.2
2.8
7.1
6.4
4.8
5.0
3.7
2.5
6.0
4.8
5.5
4.8
5.6
4.2
2.8
-30
-40
-50
-50
-35
-40
-50
-45
-50
-45
-50
-0
-5
-20
This class is
not suitable for
fluid 1
12.7
9.5
6.4
This class is
not suitable for
fluid 1
This class is
not suitable for
fluid 2
This class is
not suitable for
fluid 3
This class is
not suitable for
fluid 3
15.0
11.6
8.7
7.2
17.0
15.3
11.3
21.4
16.9
25.4
22.0
11.3
8.7
6.5
5.4
12.7
11.4
8.5
16.0
12.7
19.1
16.5
Note 1: For other temperatures consult AS4041 for appropriate pressure ratings.
Note 2: MDMT = Material Design Minimum Temperature.
457.0
457.0
457.0
5.6
4.2
2.8
6.3
4.7
3.1
5.6
4.2
2.8
6.3
4.7
3.1
This class is
not suitable for
fluid 1
-0
-5
-20
12.7
9.5
6.4
406.4
406.4
406.4
6.4
4.8
3.2
7.3
5.4
3.6
6.4
4.8
3.2
7.3
5.4
3.6
-0
-5
-20
12.7
9.5
6.4
355.6
355.6
355.6
7.1
5.3
3.5
8.0
5.9
4.0
7.1
5.3
3.5
8.0
5.9
4.0
-0
-5
-20
12.7
9.5
6.4
323.9
323.9
323.9
8.5
6.1
4.2
3.1
9.5
6.9
4.7
3.5
8.5
6.1
4.2
3.1
9.5
6.9
4.7
3.5
This class is
not suitable for
fluid 1
-0
-5
-20
-30
12.7
9.3
6.4
4.8
273.1
273.1
273.1
273.1
6.8
5.2
3.9
3.2
7.6
5.9
4.4
3.6
6.8
5.2
3.9
3.2
7.6
5.9
4.4
3.6
This class is
only suitable for
168mm diameter
maximum in
fluid 2
-10
-20
-30
-30
8.2
6.4
4.8
4.0
219.1
219.1
219.1
219.1
7.6
6.9
5.1
8.6
7.7
5.8
7.6
6.9
5.1
8.6
7.7
5.8
2.0
2.0
2.0
2.0
2.0
2.0
-15
-20
-30
7.1
6.4
4.8
168.3
168.3
168.3
9.6
7.6
11.4
9.9
10.8
8.6
12.9
11.2
9.6
7.6
11.4
9.9
10.8
8.6
12.9
11.2
2.0
2.0
2.0
2.0
2.0
2.0
2.0
2.0
This class is
not suitable for
fluid 1
-25
-30
-25
-30
6.0
4.8
5.5
4.8
114.3
114.3
88.9
88.9
Note 1: For other temperatures consult AS4041 for appropriate pressure ratings.
Note 2: MDMT = Material Design Minimum Temperature.
Ultrapipe
Circular
hollow
sections
Dimensions and Properties Handbook 95