Zinc, Paint & Accessories - Paynes Marine Group

744
Zinc, Paint & Accessories
Interlux
INtERPROtECt 2000E/2001E ®
41% solids, grey two-part epoxy. InterProtect 2000E / 2001E is a
coating developed to protect new and used fiberglass hulls from
water absorption. It can also be used to repair gelcoat blistered
hulls. On boats where the gelcoat has been removed and bare
laminate is exposed, use InterProtect 1000/1001 as a sealer coat.
• Prevents and repairs osmosis on new and blistered hulls
• Protects underwater metals such as keels, struts, shafts and
running gear
2000/2001-1L Grey 1 Litre
2000/2001-4L Grey 4 Litre
2002/2001-1L White 1 Litre
2002/2001-4L White 4 Litre
Pettit
PEttIt PROtECt
HIgH BUILD EPOxY PRIMER
A heavy-duty, high build, two component epoxy-polyamide coating
for use where maximum resistance to fresh or salt water is required.
The complete coating system is resistant to water, many industrial
chemical fumes and very humid environments. It is ideally suited to
many commercial and pleasure craft applications and has excellent
durability in exterior exposures. Like most epoxies, it will chalk if not
topcoated.
• Reduces water absorption in fiberglass hulls and prevents
osmotic blistering
• High film build for maximum protection with fewer coats
• Excellent water and chemical resistance
• Exceptional protection for steel, aluminum and other metals
• High performance system for underwater running gear
PEt4700Qt Quart
PEt4700gA Gallon
Interlux
VC PERFORMANCE EPOxY
VC Performance Epoxy is a two-part Teflon® bearing epoxy that has
a hard, slick finish ideal for use on the underwater surfaces of high
performance powerboats and racing sailboats. Teflon® adds lubricity
and eases wet sanding and burnishing.
VC Performance Epoxy’s hard, stain-resistant finish is also ideal for
rack-stored and trailered boats or boats that are kept in the water
not requiring antifouling protection. VC Performance Epoxy has no
antifouling or foul release properties.
V127KIt-S 1/2 gallon kit
V127KIt-L 2 gallon kit
Interlux
INtERPROtECt ® WAtERtItE
EPOxY FILLER
Epoxy putty for use with the InterProtect System.
InterProtect Watertite is a two-part, easy-to-use epoxy
compound for filling holes and scratches in gelcoat and
fiberglass. It is especially recommended for use to fill
blisters in an osmotic blister repair system, such as the InterProtect
Epoxy Barrier System. Its unique two-phase cure gives it a long, easyto-sand
window.
V135KIt Quart
V135KIt-SM Pint
Aquagard
AQUAgARD II SPRAY ALUMI-KOAt
A solvent based paint for use on aluminum and other non-ferrous
materials. Ideal for use on sterndrive and outboard lower unit corrosion
protection.
AQg71301 Black
AQg71310 Clear
AQg71309 Gray
AQg71307 Off White
Interlux
tRI-LUx II
Specially formulated for use on underwater aluminum surfaces such as
hulls and lower units of outboards and I/O's but is equally compatible on
fiberglass, wood or other underwater metals. Tri-Lux II does not contain
tributyltin (TBT). When properly primed, Tri-Lux II does not cause
galvanic corrosion, as do paints that contain cuprous oxide. Due to the
fast acting nature of Tri-Lux II, three full coats are recommended and
four coats should be applied in tropical waters.
Quart gallon
490-1L 490-4L Blue
n/a 491-4L Red
493-1L 493-4L Black
498-1L 498-4L White
Aquagard
AQUAgARD II ALUMA-KOtE
Designed for coating the bottom of aluminum boats, sterndrives and
outboards. The product is tin free, contains silicone, which offers similar
performance as the recently banned tin-based products for marine
applications. The paint relies on a "non-stick" principle to minimize
fouling adhesion to the surface through the use of a silicone agent.
Quart gallon
AQg80001 AQg80101 Black
AQg80006 AQg80106 Blue
AQg80007 AQg80107 White
AQg80002 AQg80102 Red